1) eccentricity
[英][,eksen'trɪsəti] [美]['ɛksɛn'trɪsətɪ]
偏心量
1.
This paper introduces a new rotation way used in turbomachinery, which is eccentricity rotation with the characteristic of assembling conveniently.
介绍了一种应用于叶轮机械的传动方式,即偏心传动,该传动方式具有装配方便的特点;将弹性接触理论应用于该传动方式偏心量的计算,建立了考虑弹性变形时偏心量的计算方法;采用一组实际数据,分析计算方法的适用性,以及弹性变形对偏心量计算的影响。
2.
When design and lamination, There is a eccentricity e of core center axes in advance and it equals to the value of yield degree in rotor center.
在设计及铁心叠片时 ,预先使铁心中心轴线有一个等于转子中心处挠度值的偏心量e。
3.
To ensure the reliability of some industry producing equipments,the rapid calibration and measurement for diameter and installed eccentricity of rotating pieces with different sizes are required.
许多工业制造装备的工作过程中,需实施不同规格回转体直径及安装偏心量的快速校准测量,以保证可靠性。
2) eccentricity in stitches
偏心量e
1.
In this paper, the relationship between eccentricity in stitches and structure properties of sewing threads is studied by means of multiple linear stepwise regression and the following result is obtained: eccentricity in stitches is most related to bending rigidity, linear density and friction coefficient of sewing threads.
本文运用相关分析和多元逐步回归分析对缝纫线迹的偏心量e和缝纫线的结构性能之间的关系进行 了研究,发现偏心量e与缝纫线的弯曲刚度、线密度和摩擦系数的关系最密切。
3) Eccentric mass
偏心质量
1.
The influences of plate damping,width,mass,inertia moment,vertical bending frequen- cy,tortional frequency,flutter derivatives,eccentric mass and distance on flutter critical velocity are analyzed in detail.
建立了用于计算对称和非对称平板颤振临界风速的数学模型;详细分析了平板阻尼、宽度、质量、质量惯矩、竖弯频率、扭转频率、颤振导数、偏心质量和偏心距等参数对颤振临界风速的影响;提出并论证了平板颤振临界风速益损系数的诺模图理论,绘制了与各参数相关的诺模图。
4) mass eccentricity
质量偏心
1.
Comparison of three measures for counteract mass eccentricity of top open typed full-automatic washing machine;
顶开式全自动洗衣机抵消质量偏心3项措施比较
2.
Farther analysis results show that: flexural vibration and torsional vibration are coupled, and the mass eccentricity is the precondition.
理论分析与计算表明:弯振与扭振是相互耦合的,质量偏心是耦合的前提;转子在圆频率为ω1的外部激励作用下,通过弯扭耦合,主要激发出频率为|Ω-ω1|的扭振。
3.
Taken mass eccentricity as control parameter, the numerical simula-tion used to analyse the characteristic of bending and torsional vibrations is accomplished.
以质量偏心为控制参数,分别对碰摩转子的弯振和扭振特性进行了数值仿真分析。
6) eccentric mass
质量偏心
1.
The effects of eccentric mass,damping,inertia force and gravity on the vibration amplitude were analyz.
在此基础上,分析了质量偏心、阻尼、惯性力和重力对振幅的影响。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条