1) speed ratio
速比
1.
Effect of speed ratio on textures transformation in cross shear rolled high purity aluminum foils;
异步轧制速比对高纯铝箔织构转变的影响
2.
The effect of speed ratio on machine efficiency;
机构的速比对机械效率的影响
3.
The effect of speed ratio on the texture of non-oriented cold rolled low silicon steel sheet was investigated after cross shear rolling at different speed ratios.
选取低硅无取向硅钢常化态板材,分别在不同速比下进行异步轧制,考察了速比对低硅无取向硅钢冷轧织构的影响。
2) ratio
[英]['reɪʃiəʊ] [美]['reʃɪo]
速比
1.
Fuzzy Logic Ratio Control of Continuously Variable Transmission System;
无级变速传动系统速比的模糊控制
2.
Discrete ratio control strategy on automobile with continuously variable transmission system
汽车无级变速传动系统离散化的速比控制策略
3.
analyzing the primary characteristic and the power performance, this article discusses the changing regularities of the ratio in two types of HTC, which have different penetrativity.
分析对比液力变矩器原始特性和动力特性 ,讨论了当外界阻力发生变化时 ,具有不同透穿性的液力变矩器速比的变化规律及其对变速器传动效率的影响 ,指出在自动变速器设计中 ,合理选择液力变矩器的结构参数 ,特别是注重其透穿度与发动机适应系数的合理匹配 ,是提高自动变速器传动效率及汽车驱动功率的有效途
3) velocity ratio
速比
1.
In present paper,the effect of velocity ratio on plane mixing layer is experimentally investigated with Particle Image Velocimetry(PIV).
本文使用PIV术对低高速侧速比为0。
2.
Only just the unlock ratio of pilot controlled check value is greater than the velocity ratio of oil cylinder,it may open up pilot controlled check value.
当液控单向阀的开启比大于液压缸的速比时,才有可能打开液控单向阀。
3.
The rotating speed relationship between two independent driving components of lapping machine was established by introducing the definition on "velocity ratio".
通过引入定义“速比”,建立了研磨装置两个独立主动件之间的转速关系。
4) transmission ratio
速比
1.
Research into distribution of transmission ratio in design of gearbox;
汽车变速器设计中速比分配问题的研究
2.
A simplified computed formula of a piezoelectric microgripper transmission organ′s transmission ratio and the angle of rotation is deduced according to the traditional method of the static equilibrium, geometric relation of mechanistic kinematics and flexible gemel.
以压电驱动式微夹钳为例进行微夹钳传动系分析,按传统的静力平衡和机构运动几何关系及柔性铰假设方法推导出其速比和转角简化计算公式。
3.
In this paper,using the L Hospital s theorem,a new method for analysis of velocity or transmission ratio of mechanisms with dead points or change points is presented.
提出了运用洛毕达极限法则分析机构通过死点或切换点时的角速度或速比的新方法 ,并具体应用于具有切换点的GRASHOFneutral机构和GALLOWAY机构的运动分析 。
5) speed-ratio
速比
1.
The speed-ratio curve of double-action parallel indexing cam mechanism has special property in shape,which makes it is not available from present transmission function,but designed purposely.
双作用式平行分度凸轮机构对速比曲线的几何形态有特殊要求,这使得该机构的速比不能从同类机构现有运动规律中得到,而必须经过特殊设计。
2.
For double-action parallel indexing cam mechanism,the characteristics of its instantaneous center curve are determined by the mechanism’s speed-ratio.
双作用式平行分度凸轮机构的速比特点,决定其瞬心线的几何特性。
6) gear ratio
速比
1.
In view of the poor generality and the difficulty in controlling clamping force and gear ratio at will of mechanical-hydraulic control system,an electro-hydraulic control system for metal V-belt continuously variable transmissions(CVT) is brought forward in this paper.
金属带式无级变速器机液控制系统通用性差,难以实现夹紧力和速比的任意控制。
2.
It is the 2nd problem of conjugate surface that solve the bearing contact of gear and the gear ratio relation under given position with two known surfaces.
已知两曲面,在既定的位置条件下,求传动的接触域及速比关系属于共轭曲面的第二类问题,也是该领域的难点问题之一,用传统的方法解决起来非常复杂。
补充资料：辊速比
分子式：
CAS号：
性质：指相邻两个辊筒线速度之比，是压延机操作中使用的术语。压延机在加工塑料薄膜或片材的时候，利用相邻压延辊线速度的不同和辊距的变化等，使塑料在压延时能更好地进行剪切、塑化，使料片顺利地从一个压辊转移到另一压辊上，从而获得规定厚度和满意质量的成品，压延机就是根据辊筒配置情况，分别称L型三辊压延机、Z型四辊压延机等。开炼机的辊速比一般为1:1.2～1:1.3。压延机擦胶时的三辊筒的速比一般为1:1.3～1.5:1(上辊：中辊：下辊)。辊筒速比的大小表示两辊间的剪切力与摩擦力的大小。密炼机的辊筒转速较快，故速比较低，一般为1:1.14～1:1.19
CAS号：
性质：指相邻两个辊筒线速度之比，是压延机操作中使用的术语。压延机在加工塑料薄膜或片材的时候，利用相邻压延辊线速度的不同和辊距的变化等，使塑料在压延时能更好地进行剪切、塑化，使料片顺利地从一个压辊转移到另一压辊上，从而获得规定厚度和满意质量的成品，压延机就是根据辊筒配置情况，分别称L型三辊压延机、Z型四辊压延机等。开炼机的辊速比一般为1:1.2～1:1.3。压延机擦胶时的三辊筒的速比一般为1:1.3～1.5:1(上辊：中辊：下辊)。辊筒速比的大小表示两辊间的剪切力与摩擦力的大小。密炼机的辊筒转速较快，故速比较低，一般为1:1.14～1:1.19
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条