2) liquid phase sintering
液相烧结
1.
Mechanism of liquid phase sintering for Al_2O_3/3Y-TZP composite;
Al_2O_3/3Y-TZP复相陶瓷的液相烧结机理
2.
Crystallization and phase changing of amorphous silicon nitride nanopowders by liquid phase sintering;
液相烧结非晶纳米氮化硅陶瓷粉体结晶与相变行为研究
3.
A study on liquid phase sintering process of hard cladding materials;
硬质覆层材料的液相烧结工艺研究
3) liquid-phase-sintering
液相烧结
1.
Experiment process of liquid-phase-sintering of high-density W-Ni-Mn alloy was introduced.
介绍了高密度合金W-Ni-Mn液相烧结的实验过程,并对烧结体密度和显微组织进行了测试和分析,发现Mn能够降低烧结温度和细化晶粒,但其高氧化性对合金的烧结工艺和性能影响显著。
4) liquid-phase sintering
液相烧结
1.
The microstructure,thermal conductivity,electrical conductivity,relative density of Mo-Cu alloy prepared by infiltration and liquid-phase sintering process are investigated.
研究熔渗和液相烧结法制得Mo-Cu合金的显微组织、电导率、致密度、热导率。
2.
08)O_4 was prepared by liquid-phase sintering process.
采用液相烧结,制备了组成为Mn_(0。
3.
The addition of ZnO led to a liquid-phase sintering mechanism of Ca 0.
４Ｚｒ４Ｐ６Ｏ２４ 陶瓷的液相烧结。
5) liquid sintering
液相烧结
1.
Reactivity in liquid sintering process of Al/fly ash particulate composites;
铝/飞灰颗粒复合材料液相烧结过程的反应性
2.
By addition of complex sintering aids to ZTA nano multiphase ceramics, liquid sintering occurred at lower temperature, so the densification process was accelerated and the relative density was improved.
在微 纳复合ZTA材料中加入少量复合助剂 ,材料在较低温度下实现液相烧结 ,促进了材料的致密化过程 ,提高了材料的相对密度。
3.
The in-situ reaction liquid sintering technical process, sintering mechanism and mechanical properties as well as its application of ternary-boride based cermet such as Mo2FeB2 based cermet(KHM) were reviewed.
介绍了三元硼化物基金属陶瓷的发展现状，以ＭＯ２ＦｅＢ２基金属陶瓷ＫＨＭ为例，对三元硼化物基金属陶瓷的原位反应液相烧结工艺过程、烧结机理和力学性能及其应用进行了综述，并对它的应用前景和发展趋势进行了展望。
6) liquid phase sinter
液相烧结
1.
The effect of the total amount of Ni and Cu on the properties of the liquid phase sintered Mo-W-Ni-Cu alloy was investigated.
研究了镍铜总量对液相烧结Mo-W-Ni-Cu合金性能的影响,结果发现,在镍铜比一定时,随镍铜总量的增加,烧结温度下降;抗拉强度σ_b先是急剧地上升,上升到最大值1100 MPa后缓慢地下降;烧结硬度在镍铜总量不超过6％时保持最高值HB 370左右,超过6％后硬度下降;晶粒则随镍铜总量增加而细化。
2.
Mo-rich Cu alloy was made with the method of liquid phase sintering the mixed Mo and Cu powder.
采用液相烧结Ｍｏ、Ｃｕ混合粉压坯的方法制取合金，分析了合金的力学性能及组织。
3.
The effect of the total amount of Ni and Cu on the properties of the liquid phase sintered MoWNiCu alloy was investigated.
研究了镍铜总量对液相烧结ＭｏＷＮｉＣｕ合金性能的影响。
补充资料：粉末液相烧结
粉末液相烧结
liquid phase sintering of powder
fenmo yex一ong shaojle粉末液相烧结(liquid phase sintering ofpowder)具有两种或多种组分的金属粉末或粉末压坯在液相和固相同时存在状态下进行的粉末烧结。此时烧结温度高于烧结体中低熔成分或低熔共晶的熔点。由于物质通过液相迁移比固相扩散要快得多，烧结体的致密化速度和最终密度均大大提高。液相烧结工艺已广泛用来制造各种烧结合金零件、电接触材料、硬质合金和金属陶瓷等。 类型根据烧结过程中固相在液相中的溶解度不同，液相烧结可分为3种类型。(l)固相不溶于液相或溶解度很小，称为互不溶系液相烧结。如W一cu、w一Ag等假合金以及A12O3一Cr、A12O3一Cr一Co一Ni、A12O3一Cr-W、BeO一Ni等氧化物一金属陶瓷材料的烧结。(2)固相在液相中有一定的溶解度，在烧结保温期间，液相始终存在，称为稳定液相烧结。如Cu一Pb、w一eu一Nl、we-C。、TIN一Ni等材料的烧结。(3)因液相量有限，又因固相大量溶入而形成固溶体或化合物，使得在烧结保温后期液相消失，这类液相烧结称为瞬时液相烧结。如Fe一eu(
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条