1) mold filling resistance
充型阻力
2) Filling ability
充型能力
1.
Influences of microstructure characteristics of semi-solid A356 alloy on filling ability;
半固态A356合金微观组织特征对充型能力的影响
2.
The study indicated effect extent of four main technology parameter on filling ability of thin-walled castings was rising pressure time, crystal pressure, degree of vacuum, filling pressure in turn.
研究结果表明,这些参数对薄壁铸件充型能力影响程度的大小依次为升压时间、结晶压力、真空度、充型压力。
3.
The results show that the traveling magnetic field foundry method by using linear motor can enhance the filling pressure head of liquid metal and effectively improve the filling ability of aluminum alloy;when the voltage is 220-250 V,the completer casting piece can be obtained by taking stainless steel as the bottom plate.
结果表明,采用直线电机移动磁场铸造法可增强液态金属的充型压头,有效改善铝合金充型能力,当电压达到220～250V之间,采用不锈钢作为铸型可以浇注出较完整的铸件。
3) Mold Filling Capacity
充型能力
1.
Effect of EPC Process on Mold Filling Capacity of Molten Metal;
消失模铸造工艺因素对液态金属充型能力的影响
4) filling capacity
充型能力
1.
A filling capacity computing model of liquid gray iron in a small diameter mould was established by combining stoppage mechanism of liquid alloy flow with the solidification theory.
结合Flemings提出的液态合金停止流动机理与凝固理论,建立了细直径型腔中灰铸铁铁液充型能力的计算模型。
2.
The vibration direction was the same as the flow direction,and the influence of mechanical vibration at different frequency and amplitude on the filling capacity of A356 and AZ91D under lost foam casting was studied.
在A356铝合金和AZ91D镁合金消失模铸造浇注过程中采用与流动方向一致的水平振动,研究不同频率和振幅的机械振动对A356和AZ91D消失模铸造充型能力的影响。
3.
Research status of adjusted pressure casting technology was reviewed from filling capacity, properties of solidification feeding and mechanical properties respectively.
介绍了调压铸造技术的原理及其工艺特点,从充型能力、凝固补缩特性、力学性能等方面评述了目前调压铸造技术的研究现状;结合实际生产应用情况,展望了我国调压铸造技术的发展前景,并对我国发展调压铸造技术提出了一些建议。
5) Filling Pressure
充型压力
1.
The results indicate that,when the filling pressure is below 30kPa,casting surface quality can be better with the filling pressure increasing;when the filling pressure reaches over 30kPa,the sand fusion,inclusion,porosity,etc appears in the casting.
结果表明:当充型压力低于30kPa时,随着充型压力增大可以得到表面质量较优的铸件;达到30kPa以上时,就出现粘砂、夹杂、气孔等缺陷。
6) aerating beam resistance grate
充气梁阻力篦板
1.
Patent and special technology of NCDRI like newly-designed inlet movable grate,thick material bed operation,NC-Ⅲaerating beam resistance grate and flexible deflection unit are used in the grate cooler.
该篦冷机采用了新设计的入口活动篦床、厚料层操作技术、NC-Ⅲ型充气梁阻力篦板和可挠伸偏转装置等南京院专有及专利技术,具有热回收效率高、冷却风量小、冷却效率高、篦板寿命长和不产生“堆雪人”现象等特点。
补充资料：肺循环阻力(或全肺阻力)
肺循环阻力(或全肺阻力)
pulmonary circulation resistance
血液在肺部血管内流动时和血管壁之间的摩擦力和血液内部的摩擦阻力。肺动脉管壁较薄，分支短而管径大，故肺动脉的可扩性较大，对血流的阻力很小，仅0.12PRU(外周阻力单位)。肺循环动脉部分总的阻力和静脉部分总的阻力相等，故血液流动时在动脉部分的压力降落和静脉部分的压力降落相等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条