说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 不可逆拉伸应变
1)  irreversible tensile strain
不可逆拉伸应变
2)  tensile strain
拉伸应变
1.
The conductors critical current (I_ c ) keeps nearly constant when the tensile strain is low than the critical value.
本文主要研究了在77K温度下,拉伸应变和弯曲应变对Bi-2223/Ag超导带材临界电流的影响,得到了超导带材的临界电流随拉伸强度、曲率半径变化规律。
2.
We discuss the changes in properties of such prepared tape compared to that of conventional Bi2223 tapes and effects of tensile strain on its properties.
本文利用在超导芯部引入Ag合金的方法制备了一种新结构Bi2 2 2 3超导带材 ,并研究了此种带材相对于普通Bi2 2 2 3超导带材性能的变化 ,以及拉伸应变对其性能的影响 。
3.
The relationship between the tensile stress and the tensile strain at the initial of a tension test has been experimentally determined and analyzed.
在稳态直流高压电场作用下,电流变液的拉伸应力在小拉伸应变范围内迅速线性增加,然后缓慢上升到拉伸屈服应力。
3)  stretching strain
拉伸应变
1.
After adopting laser precision measurement,the accuracy of the testing equipment has been increased evidently and the key problem effecting the quality of the product and the transfer method of the quality value of stretching strain have been resolved.
分析了线导线团拉伸应变激光精确测量方法及实施方案。
4)  tensile strain rate
拉伸应变率
1.
Effect of tensile strain rate on spall fracture in 20 steel;
拉伸应变率对20钢层裂特性的影响
2.
According to the curve,the spall strength,the thickness of spall scab and the tensile strain rate under different condition were obtained.
根据所得曲线波形计算出相应条件下的层裂强度、层裂片厚度以及各自的应变率,最后得到层裂强度随拉伸应变率变化的关系曲线。
5)  tensile strain meter
拉伸应变计
6)  slow strain rate test(SSRT)
慢应变拉伸
补充资料:应变
应变
strain

   由载荷、温度、湿度等因素引起的物体局部的相对变形。主要有线应变和剪应变两类。
   线应变是物体内任一点在某方向上的线元因变形产生的长度增量与原长度的比值,又称正应变。设在直角坐标系xy平面上任一A点的线元(长d)变形后在x轴上的投影为AB′(图1),则AB的长度增量为!!!Y1314_3。于是,任一点在某方向上的线元在3个坐标轴方向的线应变分别为!!!Y1314_4 ,式中uυw分别为物体中任一点沿z 坐标轴向的位移函数。线应变的正、负值表示线元的伸长和缩短。
   
   

图1 一点的线应变

图1 一点的线应变


   
   剪应变是物体内任一点两个相互垂直方向上的线元在变形后夹角的改变量(以弧度表示,角度减小为正),又称切应变或角应变。设在直角坐标系xy平面上变形前物体内任一A点成直角的两线元AB(长dx)和AD(长dy)变形后变为AB′和AD′(图2)。B′点在y方向的位移等于υ+(!!!Y1314_5)dxD′点在x方向的位移等于u+(!!!Y1314_6)dy。略去高阶项后,xy平面上A点的剪应变rxy可表示为!!!Y1314_7,同理,在yzzx平面上可得 !!!Y1314_8,!!!Y1314_9。剪应变分量具有对称性,即rxyryxryzrzyrzxrxz
   物体内某点在各方向上的应变情况称该点的应变状态。物体内任一点的应变状态可由过该点3个相互垂直平面上的9个应变分量εxrxyrxz εyryxryz ,εzrzxrzy(其中rxyryxryzrzyrzxrxz,故只有6个应变分量是独立的)通过坐标变换得出。参见应力。
   
   

图2 一点的剪应变

图2 一点的剪应变


   
   应变的时间变化率称应变率。实验证明,应变率增加时,许多材料的塑性性质变差,屈服极限(见材料力学性能)提高,应变强化(受外力作用产生塑性变形的某些金属材料,当卸载后再加载时,其屈服极限提高的现象)效应减弱。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条