1) air gap
气隙层
1.
The thermal boundary condition of the cast iron cooling stave with surface alloyed steel pipe was used for numerical simulation of temperature field and commercial software ANSYS and the method of coupling heat-structure were used to calculate thermal deformation of steel pipe at high temperature,and analyze the influence of air gap and thermal deformation on the life of cooling stave.
根据合金化管铸铁冷却壁热态试验数据确定了合金化管铸铁冷却壁温度场数值模拟的边界条件,利用ANSYS软件、采用热-结构耦合的方法计算了高温状态下合金化管铸铁冷却壁内钢质冷却水管的变形,分析了气隙层和水管热变形对合金化管铸铁冷却壁寿命的影响,得出保证合金化管铸铁冷却壁长寿的最佳气隙层厚度和相应的最佳使用热负荷。
2) gas gap
气隙
1.
A study of characteristics of gas gap heat switch and pressure adjustment;
气隙式热开关的特性研究及压力调节
2.
Finds out the Gap index that is used to judge the gas gap between the cooling wall and the carbon brick through the theory analysis and experimental research,calculates the value of Gap and confirms it reliable.
通过理论与实验研究找出一种判断高炉冷却壁出现气隙的指标Gap,计算出在不同气隙情况下Gap的取值,验证气隙指标Gap的可靠性。
3) air-gap
气隙
1.
Study on a new magnetolastic torque sensor with resistablity to air-gap variation;
新型抗气隙干扰磁弹性扭矩传感器的研究
2.
Analysis of variation in air-gap between rotor and stator in high-speed motorized spindle;
高速电主轴定转子的气隙变化及影响因素
3.
In order to optimumly select the third harmonic winding of harmonic exciting generator, the paper anlayses and calculates the air-gap magnetic field distribution of 12 kW and 50 kW harmonic exciting salient-pole synchronous gererator under no-load and full-load conditions by the finite-element method.
用限元法分析和计算了１２ｋＷ和５０ｋＷ谐波励磁凸极同步发电机空载和负载时气隙磁场分布曲线，分析了三次谐波电流分布规律和三次谐波绕组电枢反应，计算了转子转动情况下的气隙磁密时间分布。
4) air gap
气隙
1.
Study on the mechanism of air gap between H-type casts and mould;
H-型连铸坯坯壳与结晶器壁气隙形成机理研究
2.
Study of air gap formation during the mold casting Pb;
在模铸铅的过程中气隙形成规律的研究
3.
New study on the principle of air gapped core current transformer;
铁心开气隙电流互感器原理表述新探
5) gap
气隙
1.
Adjusting gap of relay springs by using laser beam;
应用激光技术进行继电器簧片气隙的校正
2.
Study of Principle and Method to Depress the Air-gap Effect for the Clamp-on Micro-current Transducer;
降低钳式微电流传感器气隙影响的方法
3.
Equivalent Cross-Sectional Area Calculation of Gaps in Core Reactor with Big Gaps;
大气隙铁心电抗器气隙等效导磁面积计算
6) Airgap
气隙
1.
The Influence of Airgap on Switched Reluctance Motor s Torque;
气隙对开关磁阻电动机转矩的影响分析
2.
O n the basis of a DSPM prototype, the magnetic field is calculated with the finit e element analysis method for various DSPM airgaps, and all the calculational re sults are disposed.
结合双凸极永磁电机的结构特点及工作原理 ,在 1 2 /8极双凸极永磁电机模型的基础上 ,采用二维磁场有限元分析法 ,在取电机气隙不同值的情况下 ,对电机内电磁场进行了仿真计算 ,并对计算结果作了分析处理 ,得出气隙大小影响电机静态特性的关系 ;对同一台原理样机 ,在取气隙不同值时对其输出特性进行了实验测试。
3.
Based on the mathematics model of EMS control system , a specific method to realize suspension control with using airgap deviation , velocity of magnetic vertical position deviation and absolute acceleration of magnetic vertical position deviation as feedback variables is prompted to improve the suspension stability .
从增强悬浮稳定性的目的出发 ,在对磁悬浮控制系统进行数学建模的基础上 ,提出了采用气隙变化、磁铁垂向位移变化速度和磁铁垂向位移变化加速度作为反馈控制量的具体控制方法 ,并在多体动力学软件SIMPACK中建立真实模型时考虑现实控制系统中轨道的激扰和控制器本身的干扰 ,最后通过对仿真结果的分析 ,得到控制的各项性能表现 ,证明了这种控制方法的可行
参考词条
补充资料：气隙
分子式：
CAS号：
性质：在挤出涂层过程中，从模口到由压辊和冷却辊所形成的间隙（被涂覆材料在此被压平和冷却）之间的距离。也指在塑料的射频加热中电极和材料表面间的距离。
CAS号：
性质：在挤出涂层过程中，从模口到由压辊和冷却辊所形成的间隙（被涂覆材料在此被压平和冷却）之间的距离。也指在塑料的射频加热中电极和材料表面间的距离。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。