1) Cylindrical surface
圆柱面
1.
Electric Field Intensity of a Uniformly Charged Cylindrical Surface With Limited Length;
有限长均匀带电薄圆柱面面上的场强
2.
Magnetic Induction of a Thin Cylindrical Surface of Limited Length Uniformly Loaded With Current;
有限长均匀载流薄圆柱面面上的磁感应强度
3.
Magnetic Induction Intensity of Electric Current on the Finite-Length-Even Cylindrical Surface
有限长均匀圆柱面电流所在处的磁感应强度
2) cylinder surface
圆柱面
1.
Partially-threaded multi-layered biaxial weft knitted fabric on a cylinder surface
纬编双轴向抽纱织物的圆柱面成型
2.
When cylinder surface and cone surface penetrate each other,if their axises intersect slantly and are parallel to the frontal projecting plane,there will he special points in the penetrating line.
本文对轴线斜交,且两轴线平行于某一投影面的圆柱面与圆锥面相贯时,相贯线上的特殊点进行探讨,从而得出了用辅助球面法不能求出该相贯线上的最右点的结论。
3) cylinder
[英]['sɪlɪndə(r)] [美]['sɪlɪndɚ]
圆柱面
1.
As for the point data are affected by noise in point cloud,the initial estimates are usually unstable that often leads to failure or incorrect result in the process of fitting point cloud to cone or cylinder.
由于点云数据中存在噪声的影响,采用基于点云数据的拟合算法对圆柱面和圆锥面拟合时进行,获得的拟合初值不稳定,从而严重影响了最终拟合曲面的准确性。
2.
With the projection restriction relationship of the cylinder and the plane being the criterion, we can finally recognize the cylinder and plane through searching among the data set of.
分别以圆柱面和平面的投影约束关系为准则 ,通过在视图的数据集中搜索各投影特征 ,识别视图中的圆柱面和平面 ,形成物体完整的表面模
3.
Through studying the intersection of paraboloid of revolution and cylinder, the author concluded that the horizontal projection of the intersecting lines—, is the famous Four-order algebra curve-Perseus curve.
通过对回转抛物面与圆柱面相交的研究,得出交线的水平投影曲线——为四次代数曲线——Perseus座曲线的结论。
4) Cylinders
圆柱面
1.
Blending of Two Cylinders with Axes in Different Plans;
两个轴异圆柱面的拼接(Ⅱ)yh
2.
In this paper,we prove that for two cylinders with axes in different planes,the GC~1 blending surface doesn′t exist between the sections in the clipping planes at some certain cases.
证明了两个轴线异面的圆柱面在与轴线斜交的平行平面截口处若干种情形不存在GC1拼接曲面。
5) cylindricity
柱面性,圆柱
6) Internal Cylinder
内圆柱面
1.
NC Form Milling for Internal Cylinder;
内圆柱面的数控端铣成形法
补充资料:椭圆柱面
椭圆柱面
elliptic cylinder
椭圃柱面[困川允勺肖回甘;,几几。uT.,ee盆.益明.月皿职pl 以一个椭回(e】】i卿)为准线的二次柱面(见二次柱面(s也faCe ofthe歇戈ondo获kr)).如果这个椭圆是实的,则称为实椭圆柱面,其方程具有下列形式: 兰二止二;. 矿’护如果这个椭圆是虚的,则称为虚椭圆柱面(仙a剔阻巧eiliptic eylinder),其方程具有下列形式: xZ .yZ 二一.十共二-二一1. aZ’b2 A.E、M班川。B撰张鸿林译
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条