1) flood parameter modification
注采参数调整
2) Adjustment of the ratio of production and injection wells number
采注井数比调整
3) injection and production adjustment
注采调整
1.
Method and effect of injection and production adjustment at the later stage of extremely high water cut recovery forⅥproducing section in Shuanghe oilfieldv
双河油田Ⅵ油组特高含水开发后期注采调整的做法及效果
4) injection-production parameter
注采参数
1.
Optimizing design of injection-production parameters of steam injection development of heavy oil in ultra-thin layer in Jinglou and Gucheng oilfields;
井楼、古城油田超薄层稠油注采参数优化设计
2.
Research on the optimizing designing method of injection-production parameters of steam soak on basis of fuzzy comprehensive judgement model;
基于模糊综合评判模型的蒸汽吞吐注采参数优化设计方法的研究
3.
This paper analyzes the development response of cyclic steam stimulation and the law of edge and bottom water invasion in block Jin91,studies the steam drive effect,rational pattern and injection-production parameters of heavy oil reservoirs with edge and bottom water,and predicts the index of steam drive stage.
在对锦91块蒸汽吞吐开发效果及边底水侵入规律进行分析的基础上,应用数值模拟方法对边底水稠油油藏蒸汽驱效果、合理井网形式、合理注采参数进行了研究,并预测了蒸汽驱阶段的指标。
5) injection-production parameters
注采参数
1.
Optimization design of injection-production parameters of steam stimulation wells;
蒸汽吞吐井注采参数优化设计
2.
The level of oil production using steam injection technique directly depends on the heat efficiency of steam injection, and the heat efficiency can be determined by injection-production parameters.
蒸汽吞吐热力采油的效果取决于由注采参数决定的注入蒸汽的热能利用程度。
6) parameter adjustment
参数调整
1.
Robustness analysis and parameter adjustment for DMC;
动态矩阵控制的鲁棒性分析及其参数调整方法
2.
The signals of underground pressure and temperature in sensor can be transferred to the parameter adjustment module on the ground numerical contr.
通过信号电缆将井下传感器的压力、温度信号上传至地面数控装置的参数调整模块,经过压力脉冲-液位数字信号转换,自行调整泵柱塞运行次数,使油井始终工作在合理的沉没度范围内,确保供排合理。
3.
Afterwards,it designs the unit selection algorithm and employs the parameter adjustment algorithm to adjust parameters like length,pitch frequency and short-term energy in the speech signal.
首先建立了由维吾尔语中的单音素、双音素所构成的小规模语音语料库,设计了相应的拼接单元挑选算法,利用参数调整算法对拼接单元语音信号的时长、基频和短时能量等特征参数进行调整,并利用时域平滑算法对拼接点处的语音参数进行调整,从而进一步提高了合成语音的自然度。
补充资料:模具加工时FANUC先行控制相关参数调整
一、0MC/0MD
参数号码 参数含义 典型设定 备注
45#3 切削进给插补后直 1 635为时间常数
线加减速有效
393#0 自动拐角降速功能有效 1 如果拐角要求
高时设1 395#2 切削进给插补后直线加 1
减速有效(先行控制)
395#3 依速度差控制拐角降速 1 482,483,
487设定
395#6 插补前直线加减速 1
类型B有效
399#2 前馈控制对切削进给 通常设0
和快移均有效
399#4 依进给类型的在位检 0
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条