1) viscous flow
粘流
1.
The shrink results from the melting of α-helix crystallites to random coil in fiber and abrupt extension results from the "viscous flow" of th.
01 MPa)及压缩应力(6 MPa)下,山羊绒单纱在219℃收缩,而在230℃突变伸长,此收缩起源于山羊绒纤维中α-螺旋结晶的熔融,突变伸长起源于山羊绒纤维的“粘流”,即山羊绒纤维结晶熔融后发生“粘流”;而在较高的拉伸应力条件(200 MPa)下,山羊绒单纱在190℃就发生突变伸长,即山羊绒纤维的“粘流”温度低于结晶熔融温度。
2) viscous/inviscid iteration
粘流/无粘流迭代
3) fluid viscosity
流体粘度
1.
The result shows that with the increase of fluid viscosity, the critical speed of the reservoir rock of middle and low permeability and medium and strong consolidation decre.
结果表明,流体粘度增加,中等强度胶结和强胶结的中、低渗透率储层岩石的临界速度降低,弱胶结的高渗透率储层岩石的临界速度降低和速敏损害程度增强。
2.
Through in - house core flow test, the effect of fluid viscosity and pH value on sand production has been studied.
了解油藏出砂机理对有效控制出砂以及选择合理的防砂方法具有重要的指导意义 通过室内岩心流动实验,研究了流体粘度以及pH值对出砂的影响。
3.
Influence of fluid viscosity, injection and production condition, injection timing and reservoir property on polymer flooding is studied on the basis of laboratory modeling, numerical simulation and pilot test in oilfield.
通过采用室内物理模拟、数值模拟和矿场实施跟踪等手段 ,研究了流体粘度、注采情况、注入时机和油藏储层对聚合物驱效果的影响。
4) highly viscous fluid
高粘流体
1.
Using stainless steel tubes(wall thick 1 mm) heated by the direct passage of a current which has a maximum about 500 A, and a aqua CMC (sodium carboxy methyl cellulose),an experimental study of flow boiling heat transfer to a highly viscous fluid in vertical downward flow is presented for a consistency index η= 0.
用大电流直接通电加热不锈钢管，进行了高粘流体流动沸腾传热实验研究，建立了流动沸腾传热给热系数关联式。
2.
n experimental investigation of flow boiling heat transfer to a highly viscous fluid in verticaldownward flow was carried out.
用高粘流体进行了垂直管内流动沸腾传热实验研究，建立了流动沸腾传热给热系数关联式。
3.
Heat transfer enhancement for highly viscous fluids in solution polymerization for synthetic rubber is an important engineering problem which can be solved effectively by using scraped-surface apparatus .
综述了工业化刮壁式搅拌器的型式、刮板形状、刮板材质及其流型、搅拌功耗和刮膜给热系数,并探讨了刮壁机构强化高粘流体传热的机理。
5) viscous flow
粘滞流动
1.
The rapid viscous flow of the bulk amorphous alloy was studied by the energy storage and the energy fast releasing.
利用储能和快速释放的方法,研究了锆基块体非晶材料在过冷液相区的快速粘滞流动。
6) flow temperature
粘流温度
1.
The flow temperature of graft copolymers was lower than that of the pure CDA and decreased with increa.
结构分析的结果表明:PCLA是通过化学键连接到CDA上;热分析表明:接枝共聚物的粘流温度(Tf)比纯二醋酸纤维素的粘流温度低,而且随着接枝率的提高,粘流温度降低。
补充资料：粘流态
分子式：
分子量：
CAS号：
性质：又称塑性态。无定形线型高聚物在较高温度或较大外力长时间作用下所处的力学状态。其特征是会产生随着时间而增长的不可逆形变（见塑性形变），产生流动的粘液。高聚物（如合成纤维和塑料制品等）的加工成型，都是在粘流态下进行的。
分子量：
CAS号：
性质：又称塑性态。无定形线型高聚物在较高温度或较大外力长时间作用下所处的力学状态。其特征是会产生随着时间而增长的不可逆形变（见塑性形变），产生流动的粘液。高聚物（如合成纤维和塑料制品等）的加工成型，都是在粘流态下进行的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条