1) interfacial strength
界面强度
1.
The interfacial strength between carbon fibre and carbon matrix in the C/C composites was determined by the single fibre push out test and the influence of type and microstructure of carbon matrix on the interfacial strength was investigated.
借助金相、透射电镜技术比较了 4种典型的炭 炭复合材料的微观结构 ,采用单纤维顶出法测定了炭 炭复合材料中的炭纤维 基体炭界面强度 ,研究了基体炭结构对界面强度的影响。
2.
The interfacial strength was measured using pyramidal diamond micro-debonding method.
用金刚锥显微脱粘法测得复合材料的界面强度。
3.
Though friction coefficient and pull-out tests,studying anti-slip performance and cohesiveness of this system,analysising the influences of friction coefficient and interfacial strength by component materials.
通过摩擦系数试验和拉拔试验,研究该系统的抗滑性和粘结性,分析组成材料对摩擦系数和界面强度的影响。
2) interface strength
界面强度
1.
The feasibility of using amplitude-frequency relationships of the multimode Lamb waves to characterize the interface strength of adhesive joints of layered planar structures has been analyzed.
对于给定的层状平面结构,将粘接层的固化过程用于模拟粘接层界面强度的变化过程。
2.
This paper reviews the development in the micro-test methods of interface strength for fiber reinforced composites.
本文对纤维增强复合材料界面强度细观试验方法的发展及现状进行了评述，分析了各种试验方法的优点和不足。
3.
In this paper, a non\|linear finite element analysis for soft cohesive ground under embankment reinforced by geotextile has been made to obtain the influence of interface strength between soil and geotextile on reinforcing effect, reinforcement effects for single and multilayer geotextile, etc.
通过非线性有限单元法分析了堤坝下软基土工织物的加筋效果,土与土工织物的界面强度对加筋效果的影响,多层土工织物的加筋效果等问题,得出了最优加筋层数、加筋垫层应力扩散效果等一系列对工程设计有用的结
3) interfacial film strength
界面膜强度
1.
Water/crude oil interfacial tension,interfacial film strength and percentage of removed water from crude oil emulsions in the presence of demulsifiers was measured.
测定了在破乳剂作用下原油乳状液的油水界面张力、界面膜强度及破乳脱水率。
5) interface bonding strength
界面结合强度
1.
Finite element simulation of a test model for interface bonding strength between coating and substrate;
涂层与基体界面结合强度测定模型的有限元模拟
2.
The influence of interface bonding strength and plastic-elastic mismatch on the fatigue crack propagation behavior was considered.
采用四点弯曲试样在高频疲劳试验机上对铝基复合层板进行了疲劳试验,采用直流电势法测量裂纹长度,用扫描电镜和光学显微镜观察其疲劳断口及疲劳裂纹形貌,通过对比性试验,考察了组元性能错配和界面结合强度对复合板L-T取向疲劳裂纹扩展行为的影响,并用断裂力学理论对其进行了初步分析。
3.
C/Cu composites with different interface bonding strength have been fabricated by adding Sn,Ni or Fe element to the copper matrix.
本文通过在Ｃ／Ｃｕ复合材料的Ｃｕ基体中添加不同的合金元素（Ｓｎ，Ｎｉ，Ｆｅ）获得不同的界面结合强度，研究了界面结合强度对Ｃ／Ｃｕ复合材料热膨胀特性的影响规律，并分析了界面结合强度对降温过程中复合材料的收缩特性及残余应变的影响。
6) interfacial shear strength
界面剪切强度
1.
The results showed that the interfacial shear strength between PBO fiber and epoxy resin were greatly improved after the modification,the.
通过单丝拔出实验研究了偶联剂对不同表面形态纤维的表面处理情况,结果表明:用偶联剂表面处理后,纤维与树脂间的界面剪切强度得到提高,偶联剂对未经烘干纤维表面处理比对烘干纤维处理的效果要好,与原丝相比,提高率可达69。
2.
A method of preparing single fiber pull-out specimens was designed,and the interfacial shear strength(IFSS) of Bf/epoxy resin composites was measured by single fiber pull-out rest.
设计了一种单根硼纤维拔出试样制备方法,并测试了不同树脂基体的硼纤维/环氧复合材料的界面剪切强度;研究了单根硼纤维拔出界面破坏过程。
3.
The single fiber fragmentation test has been used to determine the interfacial shear strength of composite materials.
单纤维段裂试验作为复合材料界面剪切强度的一种测试方法被沿用至今。
补充资料：表光合强度(见光合强度)
表光合强度(见光合强度)
forecast of sowing or transplanting time
b iaoguanghe qiangdu表光合强度见光合强度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条