1) simple operating mode
简易工况
1.
Following the principle of“new vehicle by new standard and old vehicle by new standard”,double idle speed method will be taken as basic detection method and simple operating mode for gasoline automobiles and will be put into effect in stages in the countrywide.
根据“新车新标准,老车老标准”的原则,双怠速法将是汽油车基本检测方法,简易工况法在全国范围内分步实施,柴油车将逐步采用不透光烟度计的测量方法。
2) simplified loaded mode
简易工况法
1.
Simplified loaded mode car testing bed of simulating mechanical inertia design;
简易工况法汽车检测模拟台架的机械惯量设计
2.
This article firstly introduced the methods and shortages of current motor vehicle gas exhaust inspecting, then gave a detailed account for simplified loaded mode car testing and its technology development, at the same time, put forward countermeasures to implement simplified loaded mode car testing in Jiaozhou city.
对机动车排气当前的检测方法及其不足之处进行综述,对简易工况法的发展过程进行介绍,同时提出了简易工况法在胶州市推广的思路和对策。
3) simple test of procedure
简易工况法测试
1.
This article has discussed the theoretical foundation and practice method of how to establish simple test of procedure.
汽车排放的简易工况法测试方法 ,包括三个内容 :测试运转循环、测试限值标准和测试设备。
4) Simple transient driving mode
简易瞬态工况
1.
Taking LPG taxis as researching objects,the emission factors of LPG taxis under simple transient driving mode were measured and the emission performance comparisons between LPG taxis and gasoline taxis were analyzed.
以LPG出租车为研究对象,在简易瞬态工况下测试LPG车辆的单车排放因子,对比分析了LPG车和汽油车的排放特性,研究了LPG原装车与改装车的排放差异,比较了几种不同车型的排放因子,研究了LPG出租车单车排放因子与行驶里程的关系。
5) test methods of simple driving mode
简易工况检测法
1.
Include: add checking in high idle,enhance checking and limit of λvalue for EFI vehicle,emission limits of two-speed idle were regulate for EFI vehicle,two fuel were test separately for bi-fuel vehicle,test methods of simple driving mode were added,the principle and method of confirm limits for exhaust pollutan.
主要包括:增加高怠速排污检测、对电喷汽车增加过量空气系数(λ)的限定、新规定了国1以来的在用汽油车双怠速排放限值、双燃料车要对两种燃料分别检测、对简易工况检测法作了规定、制定简易工况检测法排放限值的基本原则和方法、供地方参考的排放限值等。
6) VMAS
简易瞬态工况法(VMAS)
1.
Analysis on Influence Factors to Measurement Accuracy of VMAS
影响简易瞬态工况法(VMAS)测量精度因素分析
补充资料：泵工况点
分子式：
CAS号：
性质：泵完成输送液体必须具有一定的流量和一定的排出压力。在泵运行中某一时只能有一种相对应的流量和排出压力，这就是泵在此时的工况点。在实际应用时，泵的工况点：离心泵等叶片泵以流量和相对应的扬程表示；往复泵等容积泵以压差和相应的流量表示。以泵的性能曲线表示时，叶片泵的流量和扬程曲线、容积泵的压差和流量曲线与泵排出系统的阻力曲线的交点，即为该泵的运行工况点。
CAS号：
性质：泵完成输送液体必须具有一定的流量和一定的排出压力。在泵运行中某一时只能有一种相对应的流量和排出压力，这就是泵在此时的工况点。在实际应用时，泵的工况点：离心泵等叶片泵以流量和相对应的扬程表示；往复泵等容积泵以压差和相应的流量表示。以泵的性能曲线表示时，叶片泵的流量和扬程曲线、容积泵的压差和流量曲线与泵排出系统的阻力曲线的交点，即为该泵的运行工况点。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条