1) maximum welding speed
最大焊接速度
1.
A detailed CO2 laser-MIG (metal inert gas) hybrid welding experiment was carried out on the 4mm mild plates to discuss the relation of laser power, arc current, the maximum welding speed and the weld shaping, as well as the joint gap.
对此,采用4mm厚Q235钢板进行了CO2激光-MIG(metalinertgas)复合焊接研究,探讨了激光功率、电弧电流对最大焊接速度的影响及其和接头间隙对焊缝成形的影响规律。
2) welding speed
焊接速度
1.
Relation of welding speed and heat input at aluminum alloy friction stir welding
铝合金搅拌摩擦焊时焊接速度与热输入的关系
2.
The impact of different welding speeds on the low-cycle corrosion fatigue life of 12Cr18Ni10Ti steel sheets in corrosive media was studied and the results showed that,at the same welding process parameters,the low-cycle corrosion fatigue life of steel sheets welded at the speeds ranging from 60 m/hr.
文章研究了不同的焊接速度对12Cr18Ni10Ti薄板在腐蚀性介质中的低用腐蚀疲劳寿命的影响。
3.
The effect of processing parameters including laser power,welding speed and protection gas flow on the welding quality was researched in this paper.
探讨了焊接工艺参数包括激光功率、焊接速度、正反面保护气体流量对焊接效果的影响。
3) maximum velocity
最大速度
1.
The analysis and research of the elevating velocity efficiency and the maximum velocity;
对提升速度效率与最大速度的分析研究
2.
The position of the maximum slider velocity in different type of slider-crank mechanism has been researched in this paper,some conclusions have been obtained,with regard to the offset slider-crank mechanism,the maximum velocity of slider is in the position where crank and linkage are in right angle,but to the centric slider-crank mechanism,the .
根据滑块工作行程的最大速度与平均速度的比值要求设计曲柄滑块机构,首要问题是确定滑块工作行程的最大速度位置。
4) maximal speed
最大速度
1.
Using qualitative analysis and getting maximal speed by numerical value calculation,the author draws the conclusion that the two objects are unlikely to be under no stress and their speeds can t possibly reach maximum at the same time,correcting the wrong solutions to the problems about maximal speed in the papers of the physics contest.
针对物理竞赛试题中一类力学求最大速度问题的错误解答,用中学物理和导数的知识进行定性分析并通过数值计算,求出了物体的最大速度,从而得出结论:试题中两物体不可能同时处于受力为零的状态,速度不可能同时达到最大值,纠正了这类试题的错误解答。
2.
More and more researches indicate that maximal speed is the key factor to improve 100-meter performance.
越来越多的研究表明,最大速度是提高100 m成绩的关键。
3.
As a conclusion,the maximal speed and the continuous extension at the highest speed is the tendency of the current dash sports.
对第六届和第七届世界田径锦标赛男子100m决赛运动员的成绩进行对照分析,结果表明最大速度不断提高和最大速度的持续延长是当前短跑运动的发展趋势。
5) maximum speed
最大速度
1.
It is a relation of unite of opposites between maximum speed and keeping distance in 100m running.
100m跑最大速度和保持距离是对立统一的关系;绝对速度和最大速度是两个不同的概念,绝对速度是最大速度的基础,适当降低最大速度显著增加其保持距离,两者合理搭配才能取得100m跑优异的比赛成绩。
6) Maximum tire ground speed
最大轮胎接地速度
补充资料：飞机最大速度
飞机在发动机最大功率或最大推力工作时能达到或允许达到的速度。通常指平飞最大速度和最大允许速度。使用发动机最大功率或最大推力平飞所能达到的速度为平飞最大速度。为保证飞机结构强度不致破坏，安定性、操纵性不致丧失，而规定不得超过的飞行速度为最大允许速度。%r7q
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条