1) molecular shape factor
分子形状系数
1.
Based on the Mie potential function theory and London dispersion forces theory, and with the introduction of Leland’s molecular shape factors to modify the inadequacy of the two parameters corresponding states principle for complex fluids, a new correlation for binary interaction parameters of the equation of state was proposed.
针对偏离二参数对应状态原理的复杂流体,以Mie势能函数和London色散力理论为基础,引入基于Joffee和Stewart虚拟临界规则的Leland分子形状系数,推导得到状态方程中二元相互作用参数kij的新型关联式。
2) form factor
形状系数，波形系数，波形因子，形状因子
3) molecule shape index
分子形状指数
1.
On the basis of the characteristics of atomic types in molecule,Hall's electrotopological state indices(E_n) and Kier's molecule shape index((()~mK)) are calculated for 117 alkanes,cyclanes,aliphatic alcohol,aliphatic ketones.
本文计算了117种烷烃及其衍生物的两类拓扑指数值:其一是基于原子类型特征的电性拓扑状态指数(En),其二为Kier的分子形状指数(mK)。
4) shape factor
形状系数，波形因数，波形系数，成形系数，波形因子，形状因子
5) shape coefficient
形状系数
1.
Improved load shape coefficient method in low voltage line loss calculation
低压电网线损计算中的改进形状系数法
2.
25mm)and shape coefficient on the settling velocity were discussed,finally three correlative mathematical models were set up,which established the theoretical foundation for studying WMFS's fluidization and technological parameters.
25mm)及形状系数对沉降末速的影响,最终建立了3个相关的数学模型,为水介质流化床分选机流态化以及工艺参数研究奠定了理论基础。
3.
This paper put forward a new method, in which digital elevation model (DEM) was used to differentiate sub-basins and to extract average slope and maximum length of flow concentration which makes a positive contribution to calculate shape coefficient.
提出一种方法,利用数字高程模型(DEM)划分子流域,提取各单元流域的平均坡度和最大汇流路径长度,以最大汇流路径长度推求形状系数,并将形状系数和平均坡度引入模型结构中,建立其与汇流参数之间的相关关系,使新安江模型能同时考虑降雨、流域形状以及地形分布。
6) shape factor
形状系数
1.
Atrium shape factor and plume equations;
中庭的形状系数与烟羽方程
2.
An equipment used to determine the shape factor of catalyst was established in this paper.
建立了测量催化剂颗粒形状系数的实验装置。
3.
By choosing the structure of spread model and the mathematical analysis of the shape factor of rollpass, a designing idea to obtain geometric shape according to strain factor has been built.
通过对宽展模型结构型式的选择和孔型形状系数的数学分析，建立了根据变形系数寻找几何形状的设计思想。
补充资料：变形区形状系数
变形区形状系数
parameters of deformation zone
b ianxingqu xingzhuang xishu变形区形状系数(parameters of deformationzone)通常指反映变形区几何特征及这些特征在轧制过程中对应力状态影响程度的轧件和工具尺寸的。~一~一，二。，了二H十川，，，。小二，，~参数，主要有z仄、R仄(万一号二}，H/D或从/D。式中D、R、H、h、万、l分别指轧辊直径、轧辊半径、轧件轧前厚度、轧件轧后厚度、轧件平均厚度、变形区长度。 (余望)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条