1) slide wedge angle
斜滑块角度
1.
The paper analyzes the sliding of the straightener of 8 MN tension at the clamp during extension and gets the idea that the main reason is the influence of the slide wedge angle and puts forward some measures to be taken.
分析8MN张力矫直机在拉伸过程中经常出现的钳口打滑问题,其钳口打滑的主要原因是斜滑块角度的影响,分析影响斜滑块角度的因素,并提出解决措施。
2) inclined sliding block
斜滑块
1.
The key points in designing the side core-pulling mechanism with inclined sliding block were stated in detail.
分析了烟花尾翼塑件的结构特点,介绍了该塑件注射模的结构、工作过程及制造特点,重点阐述了斜滑块抽芯机构的设计要点。
3) slanted slide
斜滑块
1.
the problem of demoulding was solved using core-pulling mechanism combining slide and slanted slide.
巧妙地利用滑块与斜滑块联合抽芯机构解决此类塑件的脱模难题。
2.
The core-pulling structure with a slanted slide has solved the difficulty of one mould with multiple cavities.
采用斜滑块抽芯 ,解决了一模多腔的难点 ;采用二级推出使操作简易 ,模具更可
3.
The structure with a slanted slide was used to the mould for solving the problems of core pulling and mould reposition for the inner side holes at the top and bottom of the plastic part.
介绍了民用手提式电瓶瓶盖的成型工艺及注射模结构 ,为解决塑件上、下部内侧孔的抽芯和复位 ,模具采用了斜滑块结构 ,可自动抽芯、复位 ,提高了生产效
4) slanting slide
斜滑块
1.
The ejection mechanism used pin ejector to pull the plastic parts out with move slanting slide simultaneously leaving circular arc concave position.
脱模机构采用推杆推出塑件的同时带动斜滑块脱出圆弧形凹位,使脱模机构简单实用。
5) Inner sliding block
内斜滑块
6) outer inclined sliding block
外斜滑块
1.
This mould uses two outer inclined sliding block to form the ball cavity,uses the symmetrial surface of the workpiece as the bisection surface of the two outer inclined sliding block,and this outer inclined sliding block can eject the casting.
框体上圆球的型腔由两外斜滑块形成,以工件对称面作为两外斜滑块的对分面,外斜滑块还兼起推出铸件的作用。
补充资料：斜楔滑块装置
斜楔滑块装置（图1）的主要作用是把压力机的垂直向下运动，通过斜楔驱动器使装在模具上的滑块产生水平方向的运动，形成级进模的浮动抽芯部件、横向冲孔部件、弯曲成形部件，或冲件出件部件。
图1 斜楔滑块装置 |
斜楔驱动器的驱动角一般是与垂线成40°～50°。
单动式斜楔驱动滑块，由弹簧使滑块复位。其缺点是弹簧失效，会造成机构失灵。
双动式斜楔一般用于冲件成形后，凸凹模之间具有一定的卡住力及要求滑块往返位置正确的模具。缺点是斜楔较长。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条