1) critical joint size
临界节理尺寸
1.
The results show that there exists a critical joint size(CJS) by which the size effect of the shear strength parameters of fractal rock joints ca.
数值直剪试验结果表明:岩石分形节理存在消除抗剪强度参数尺寸效应的临界节理尺寸(CJS)。
2) critical dimension
临界尺寸
1.
The model was analyzed and established,then the formula of critical dimension was got,which was related to the temperature distribution of heater tip.
根据传热学建立了脉冲热压焊的焊咀温度分布模型,对该模型进行分析、计算,得到了焊咀端部温度分布是否分布均匀的临界尺寸公式。
2.
The results showed that the critical dimension for Poplar increased wh.
02 MPa的真空干燥条件下,通过未封面与侧面封闭试件的对比试验,对杨木真空干燥临界尺寸进行了研究。
3) Critical size
临界尺寸
1.
Research on critical size of water barrier in underground coal mine;
论井下隔水煤柱承压破坏的临界尺寸
2.
Quantitative prediction of critical size for the formation of semiconductor quantum dots;
半导体量子点形成临界尺寸的定量预测
3.
The progress on characterization(including HRTEM, SFM, XRD and Raman spectra), critical sizes(including the single-domain critical size and the ferroelectric critical size)and the species of domain(including c domains, a domains, 180° domains and 90° domains)in ferroelectric thin films are reviewed.
综述了铁电薄膜中电畴的表征方法(高分辨透射电镜、扫描力显微镜、X射线衍射、拉曼光谱等)、类型(c畴和a畴、180°畴和90°畴等)、临界尺寸(单畴临界尺寸和铁电临界尺寸)等方面的研究进展,提出了研究中需要解决的一些问题。
4) critical nucleus size
临界核尺寸
5) minimum cri tical size
最小临界尺寸
6) critical inclusion size
临界夹杂物尺寸
1.
The critical inclusion sizes (CIS) of some steels with given matrix hardness or tensile strength and surface roughness under high cycle fatigue condition were estimated mainly on the basis of Murakami's theory, i.
依据Murakami的“夹杂物等效投影面积模型”估算了在高周疲劳条件下一定硬度(或强度)高强钢的“临界夹杂物尺寸:。
补充资料：临界尺寸（criticalsize）
临界尺寸（criticalsize）
见“超导体小样品”。它也是超导电性尺寸效应物性呈现的标志。由GL理论所得的若干结果如下：
厚为2d的超导薄膜，磁场平行于膜面：
`d_K=sqrt5\delta_0//2`
半径为r的超导球体：
$r_K=sqrt{21}\delta_0//2$
纵向和横向磁场中半径为r的超导圆柱体均为：
$r_K=sqrt3\delta_0$
对于“长轴半径$a\gt\gt$短轴半径b”的超导椭球体，在纵向磁场中：
$L_K\equivb=sqrt{3//2}\delta_0$
在横向磁场中：
$L_K\equivsqrt{ab}=sqrt{7//\pi}\delta_0$
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条