1) three-zone lumped parameter
分区集中参数
2) distributed-concentrated parameter method
分相集中参数法
1.
For the evaporator and condenser,the models were established by distributed-concentrated parameter method in each zone.
根据系统各部件的特点,用分布参数法建立了太阳能集热器的动态参数模型,用分相集中参数法建立了冷凝器和蒸发器的数学模型,用集中参数法建立了压缩机和电子膨胀阀的数学模型,并给出了模型的求解方法,为下一步计算机仿真奠定了基础。
3) lumped parameter
集中参数
1.
The paper analyzes and compares the lumped parameters that are replaced the distributed parameters of actual cable for intrinsically safe explosion-proof test.
针对在本安防爆检验中用集中参数代替实际电缆的分布参数进行了分析比较,此方法在实际本安性能检验中得到了具体的、广泛的应用。
2.
Aimed at the deficiency of multi-terminal transmission line fault location at present,combining with the fault location algorithm of transmission line which does not have branch,the author proposed the fault circuit identification method of T-connection transmission line,and solved the fault location with the lumped parameter circuit model and the distributed parameter circuit model.
针对当前多分支输电线路故障测距的不足,结合无分支输电线路的故障测距算法,提出T接输电线路的故障分支识别,并采用集中参数线路模型和分布参数线路模型求解故障距离。
3.
Describes a frequency multiplier of step recovery diode with lumped parameter from tens MHz to hundreds MHz.
介绍了一种从几十兆赫到几百兆赫的集中参数式的阶跃恢复二极管倍频器，并对其电路及实验结果分别进行了讨论。
4) concentrated parameter
集中参数
1.
Based on the theory of the concentrated parameter, a three-dimensional dynamic model with 12 degrees of freedom for the spiral bevel gear transmission system was developed, where the flexional, torsional, axial and rotational motion were considered.
基于集中参数法建立了弧齿锥齿轮的多自由度弯-扭-轴-摆耦合振动三维空间十二自由度动力学模型。
2.
Based on the theory of the concentrated parameter,a three-dimensional dynamic(model) with multiple degrees of freedom for coupling vibration of a spiral bevel gear transmission system was developed,in which the flexional,torsional,axial and rotational motions were considered.
基于集中参数理论,建立了弧齿锥齿轮的多自由度弯曲-扭转-轴向移动-扭摆等耦合振动的三维空间动力学模型。
3.
The concentrated parameter method and the movable boundary method are used to set up the simulation system of the once-t.
新型直流蒸汽发生器采用双面传热的双层套管结构,一次侧的单相流体分别在内、外侧强迫流动,二次侧经过相变的流体逆向强迫流动,根据这些特点,对其进行热工和水力分析,采用集中参数处理方法和可移动边界法,建立了直流蒸汽发生器的数学模型和仿真系统。
6) distributed model of long tube
分段集中参数模型
补充资料：集中参数控制系统
分子式：
CAS号：
性质：组成控制系统诸环节的参数不随空间坐标变化的控制系统。
CAS号：
性质：组成控制系统诸环节的参数不随空间坐标变化的控制系统。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条