1) latex
[英]['leɪteks] [美]['letɛks]
乳胶
1.
Analysis of the Water-soluble Proteins in Medical Latex Gloves
医用乳胶手套中水溶性蛋白质的含量分析
2.
The influence of the composition, ratio of network Ⅰ to network Ⅱ, the kinds and amounts of crosslinker on miscibility and damping properties of multicomponent latex interpenetrating polymer networks (LIPNs) were investigated with a rheovibron viscoelastometer.
用动态粘弹谱仪研究多组分乳胶ＩＰＮ’ｓ 体系网络的组成、配比、交联剂品种及用量等因素对体系相容性及阻尼性能的影响。
3.
The super microstructure of the outer coating of some natural latex catheters made in China and abroad with TEM was described.
用透射电镜（ＴＥＭ）观察研究了国内外几种天然乳胶导尿管外涂层的超微结构，并与其性能作了比较，结果表明，涂层的厚度和均匀度及对胶层的渗透程度直接影响产品的使用性能。
2) emulsion
[英][ɪ'mʌlʃn] [美][ɪ'mʌlʃən]
乳胶
1.
The initiator is summarized in grafting copolymerization preparation emulsion with using starch and ethenyl monomer , each kind of initiator mechanism is commented, influence of the initiator selecting to the emulsion performance is elaborated.
总结了淀粉与乙烯基单体接枝共聚制备乳胶常用的引发剂,对各类引发剂的机理作了评述,讨论引发剂的选用对乳胶性能的影响。
2.
The process of manufacturing emulsion products and its capacity indexes have been analyzed in this paper.
本文分析了乳胶制品的生产过程，并对工序能力指数进行了分析，从而推断出产品的质量。
3.
Methods: A random, single blind, positive-control and multi-center clinical trial recruited 230 patients with osteoarthritis, who were randomly applied onto the affected area with either piroxicam patch (n = 116) once every other day or diclofenac emulsion (n = 114) three times per day for 14 days.
方法:研究采用多中心、随机、单盲、阳性药(双氯芬酸乳胶)平行对照。
3) latex adhesive
乳胶
1.
The polyacrylate latex adhesives have been synthesized to meet the requirements of the development of the coated abrasives products.
根据砂布磨具对胶粘剂的性能要求 ,合成了聚丙烯酸酯乳液胶粘剂 ;考察了共聚体系中各种原料的组合、配比及用量对乳胶机械性能的影响。
4) latexes
乳胶
1.
The results show that the rate of polymerization increases with increasing emulsifier concentration, initiator concentration and temperature, the nucleation period finishes earlier and the particle average diameter of latexes is larger than the particle produced by traditional emulsion polymerization.
对反应性乳化剂作用下的醋酸乙烯酯(VAc)乳液聚合动力学体系进行了研究,实验结果发现,聚合速率随乳化剂、引发剂浓度、温度的增大而加快,乳胶粒平均直径较传统的的乳液聚合乳胶粒子大得多,且成核期结束较早。
5) natural latex
乳胶
1.
The different contents of nano SiO x surface actively modified with complex dispersants were homogeneously dispersed in the macro expansion natural latex.
通过用复合分散剂对纳米SiOx进行表面改性处理后 ,将不同份数的纳米SiOx均匀分散于微发泡天然乳胶配方材料中 ,经硫化后 ,对其力学性能所受到的影响做了相应的研究。
2.
Hence, the antibacterial natural latex has been researched for expanding its applications in the filed of biology medical area.
天然乳胶由于其优良的性能已被广泛应用于医疗领域。
6) latex
[英]['leɪteks] [美]['letɛks]
胶乳
1.
Experiment of salt-resisting performance of polyvinyl alcohol latex oil-well cement;
聚乙烯醇胶乳油井水泥抗盐性能实验
2.
Synthesis of large particle polybutyl acrylate latex;
大粒径聚丙烯酸丁酯胶乳的制备
3.
Improvement of latex on mechanical deformation capability of cement sheath under triaxial loading condition;
胶乳对水泥石三轴力学形变能力的作用
补充资料：乳胶
| 乳胶 latex 泛指聚合物微粒分散于水中形成的胶体乳液。又称胶乳。习惯上将橡胶微粒的水分散体称为胶乳，而将树脂微粒的水分散体称为乳液。以乳胶为原料制成的制品称乳胶制品，常见的如海绵、手套、玩具、胶管等。 乳胶可分为天然、合成和人造3类 。①天然乳胶是橡胶树割胶时流出的液体，呈乳白色，固含量为30％～40％，橡胶粒径平均为1.06微米。新鲜的天然乳胶含橡胶成分27％～41.3％(质量)、水44％～70％、蛋白质0.2％～4.5％、天然树脂2％～5％、糖类0.36％～4.2％、灰分0.4％。为防止天然乳胶因微生物、酶的作用而凝固，常加入氨和其他稳定剂。天然乳胶主要用于制作海绵制品、压出制品和浸渍制品。②合成乳胶一般通过乳液聚合制得，如聚丁二烯乳胶、丁苯乳胶等。为使固含量达到40％～70％，首先使橡胶微粒附聚成较大的颗粒，再采用与天然乳胶相似的方法浓缩。合成乳胶主要用于地毯、造纸、纺织、印刷、涂料及胶粘剂等工业部门。③人造乳胶是一种非乳液聚合的橡胶乳胶。向溶液聚合生成的胶体中加入水和表面活性剂，使橡胶微粒分散于水中，然后蒸除溶剂制得。如果橡胶不能充分溶解于溶剂中，可将生胶和胶料在含有乳化剂的水相存在的条件下，不断捏炼，直至形成稳定的橡胶水分散体。人造乳胶与合成乳胶的用途基本相同。 |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条