1) relative impact energy
相对冲击功
1.
The microstructures of high manganese steel impacted with different relative impact energy(50、100 and 200 J/cm~2) were investigated with optical microscopy and transmission electronic microscopy and the work hardening mechanism of the steel was also analyzed.
通过模拟实际工矿条件,研究了不同相对冲击功条件下高锰钢加工硬化后的组织变化。
2) relative wallop
相对冲击力
3) relative impact strength
相对冲击强度
4) Impact energy
冲击功
1.
Investigation on the correlation between fracture toughness and impact energy for middle strength steel;
中强钢断裂韧性和冲击功关系的研究
2.
Comparison of two kinds of models to predict the impact energy of the hot rolled Q235B in MaGang;
Q235B热轧板冲击功人工神经网络与线性回归预报模型的比较
3.
The results show that the impact energy increases and the yield strength decreases slowly with increasing the tempering temperature in the range of 200~600 ℃,and the impact energy increases and the strength decreases sharply when the tempering temperature is increased to above 600 ℃.
结果表明,25CrNi3MoV钢在200-600℃范围内回火时,随回火温度的升高,屈服强度缓慢下降、冲击吸收功缓慢增大;600℃以上回火时,强度急剧下降、冲击功迅速升高。
5) impact power
冲击功
1.
Influence of impact power on impact-corrosion resistance of low carbon high alloy steel;
冲击功对低碳高合金钢冲击腐蚀磨损性能的影响
2.
The property of impact-corrosion resistance of the low-carbon hi-alloyed steel has been tested in different impact power with the reconstructive impact-corrosion resistance machine.
利用改造的冲击腐蚀磨损机,测试了不同冲击功下低碳高合金钢的冲击腐蚀磨损性能。
3.
The results indicate that although the impact frequency of DTH hammer decreased somehow, the impact power increased.
结果冲击频率虽然有所下降 ,但其冲击功却有升高的趋势。
6) Impact work
冲击功
1.
The Un -qualified Reason Analysis of the Impact Work for Grade 35 Steel Forging Used for Pump Shaft;
35钢泵轴锻件冲击功不合格原因分析
2.
The linear relation between crushing specific work and the impact work and the temperature of ice.
研究冰在冲击载荷作用下发生破碎的状态,提出破碎比功的概念,分别建立了破碎比功与温度和冲击功的线性表达式。
3.
The results show that for the samples with remaining casting microstructure after normalizing,its tensile strength and elongation can be up to standard,and its fracture contraction rate reduces a little,but its impact work becomes lower than the samples with normal microstructure.
结果表明,正火不充分而残留铸态组织的铸钢试样,抗拉强度、伸长率均能达标,断面收缩率稍低,但冲击功却比正常组织试样低很多。
补充资料:相对冲击强度
分子式:
CAS号:
性质:同一材料的缺口试样与无缺口试样,或两种不同缺口形状的试样所得冲击强度值之比。这是材料作简支梁或悬臂梁冲击试验时研究缺口敏感程度的一种度量方法。
CAS号:
性质:同一材料的缺口试样与无缺口试样,或两种不同缺口形状的试样所得冲击强度值之比。这是材料作简支梁或悬臂梁冲击试验时研究缺口敏感程度的一种度量方法。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条