1) turning temperature
车削温度
1.
By means of 3D-FEM for distribution status of turning temperature and st.
通过车削温度场与应力场的三维有限元模拟,分别得到刀-屑接触区最高温度、车削力与进给力相对车削位移的变化规律。
2) grinding temperature
磨削温度
1.
Experimental study on grinding temperature of porous metal bonded diamond grinding wheels;
金属结合剂金刚石多孔砂轮磨削温度的实验研究
2.
Theoretical Analysis and Experimental Research on Grinding Temperature of Carbon Fiber Reinforced Composites;
碳纤维复合材料磨削温度理论分析与试验研究
3) Milling temperature
铣削温度
1.
The milling temperature experiment was processed by improved semi-manu al thermocouple method.
进行了铣削温度试验 ,采用改进的人工热电偶法 ,利用动态数据采集系统 ,对波形刃铣刀片的铣削温度进行了采集。
2.
Milling temperature is an important reason of wear and fracture of milling insert.
铣削温度是造成铣刀磨损、破损的一个重要原因，多年来，人们对铣削温度的研究基本局限于铣刀片的平均温度方面。
4) cutting temperature
切削温度
1.
Development of the dynamic measurement system of cutting temperature based on computer technology;
切削温度计算机动态测试系统的研制开发
2.
A virtual instrument for measuring cutting temperature and cutting force;
切削温度与切削力综合测量的虚拟仪器
3.
The milling mechanism of Ti6Al4V was studied by means of comparing cutting temperature,cutting force,cutting vibration and chip deformation based on average cutting thickness.
选用航空领域应用最广泛的钛合金TC4,基于平均切削厚度进行大量铣削试验,通过切削温度、切削力、切削振动、切屑变形等方面研究其铣削机理。
5) Drilling temperature
钻削温度
1.
Drilling temperature and its temperature distributing was studied using a thermal imaging device and it is indicated that the drilling heat is mainly produced from the friction between drilling bit backface and machind surface,and the higher the rotary rate,the higher the drilling temperature,and the higher the feedrate,the lower the drilling temperature.
利用热像仪对碳 /环氧复合材料高速钻孔时的钻削温度及温度场分布进行了系统的试验研究。
2.
Experience formulas were developed to predict drilling torque,thrust force and drilling temperature with multiple linear regression analysis model.
为了得到钻头直径与钻削参数对钻削力和钻削温度的影响规律,故用高速钢标准钻头对1Cr18Ni9Ti与45钢进行了钻削对比试验,并用多元线性回归模型建立了钻削力和钻削温度的经验公式。
3.
Applying to the LabVIEW development platform and combining with ADLINK PCI-9118 data acquisition modules,a drilling temperature Dynamic measurement system by semi-manual thermocouple method is designed,It concludes the data acquisition,data processing,data analysis,data storage and so on.
介绍了一种基于LabVIEW开发平台与凌华PCI-9118数据采集卡相结合,并以半人工热电偶法为测温方法的钻削温度动态测试系统,具有数字及图形显示、数据存储、数据回放、数据处理等功能。
6) turning precision
车削精度
1.
Use positive feedback adjusting to improve turning precision of hydraulic profiling tool slide;
用顺馈校正来提高液压仿形刀架的车削精度
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条