1) edible pastes processing
酱制作工艺
2) manufacturing process
制作工艺
1.
A manufacturing process of high performance coated sand phenolic resin was introduced.
介绍了一种高性能覆膜砂用酚醛树脂的制作工艺。
2.
It discusses the feasibility of the manufacturing process and presents the actual manufacturing process and matters needing attention.
介绍井下矿用电力电缆发生故障时,如何使用加长型热缩电缆接头,对其制作工艺的可行性进行讨论,并论述了实际的制作工艺和注意事项。
3.
The manufacturing process is also described in detail in this paper.
介绍一种新型铁路用玻璃钢操纵台 ,并对其制作工艺加以详细论述。
3) processing technology
制作工艺
1.
Study on the processing technology of novel sacchariferous starter for Chinese liquor;
新型白酒糖化发酵剂的制作工艺研究
2.
Investigation on processing technology of flavoring paste made from straw mushroom and garlic with nutritional and healthy functions was reported.
2%的基本配料比例以及合理的制作工艺,可得到品质风味优良的调味酱产品。
3.
The low-sugar and compounded jam,rich nutrition and fragrance, was made from fig, apple, sugar and thickening agents by appropriate processing technology.
以无花果、苹果为主料,辅之以蔗糖和增稠剂等配料,不添加任何防腐剂、香精、色素,采用合理的制作工艺,制成了营养丰富和风味俱佳的低糖无花果复合果酱。
4) fabrication process
制作工艺
1.
The paper systematically introduced the current situation of fabrication process of the leather in china, and also analyzed the aduantages, disadvantages in the process.
系统地介绍了我国皮革制作工艺的现状,分析了皮革多种制作工艺的优点与缺点及其适用类型,对其中一些工艺提出了改进方法,并对我国皮革制作工艺的发展方向提出了一些自己的见解。
2.
Also the fabrication processes are studied systematically.
本文研究了3英寸372×276象素a—Si TFT有源矩阵的优化设计理论,讨论了材料物理参数和器件结构参数对器件性能的影响,并对其制作工艺进行了系统研究。
3.
Also particularly explains the superior characteristics,fabrication process and installation of the compound air duct,in addition,analyzes the economic feasibility of the substitute project.
详细讲解复合风管的优越性能、制作工艺及风管的安装,并以工程实例分析替代方案的经济可行性。
5) fabrication technology
制作工艺
1.
Analyzed fabrication technology of large-size barrel.
剖析了大型筒体的制作工艺,以及筒节卷制、焊接、机加工到筒节组对等过程的质量控制;介绍了为提高筒体制作质量所采取的一些措施。
2.
The merit and defect of these technologies were analyzed, and the development of fabrication technology were summarized.
综述了二元光学元件的常用制作工艺技术,包括台阶刻蚀法、薄膜沉积法、直接写入法、准分子激光加工法和灰阶掩模法。
3.
Some limitations and defects have been found out about fabrication technology, material property, system models, and interface design, etc.
从制作工艺、材料特性、系统模型的确立及接口设计上详细分析了性能约束因子。
6) Manufacture technology
制作工艺
1.
Their structure and manufacture technology has been described.
文章介绍了经多年研制而成的 ,直径分别为 :30mm、45mm、6 0mm和 10 0mm的系列行波型超声波电机 ,描述了它们的结构 ,阐述了电机制作工艺 ,并对电机性能进行了实测和分
2.
Raw material,manufacture technology and product character of Preparation HAP powder from Fisheries Wastes was introduced on the paper.
介绍了以鱼类下脚料生产风味水解蛋白粉的制作工艺及产品的相关技术特征。
3.
The manufacture technology of the spindle system of the vacuum tumbler was one of the most important aspects for its working reliability.
滚揉机主轴系统的制作工艺水平对滚揉机的工作可靠性具有很大的影响。
补充资料：西周骨器制作工艺
西周骨器制作工艺 一九七六年，在陕西扶风云塘，发掘丁一处西周骨器作坊，清理出骨器近二百件，出土了两万多斤废骨料，大量骨器半成品，绝大部分带有锯、削、锉、磨等加工痕迹。同时还出土铜锯、铜刀、铜钻和砺石等制骨工具，这对当时骨器制作工艺有了较明确的认识。举骨笄为例：１、选材。以兽类骨骼的关节部位（骨臼和关节头）为最多，如肱骨、桡骨、尺骨、掌骨和肩胛骨前缘、后缘等，占总量百分之九十。可见，兽类的四肢骨，是制造骨器的主要原料。２、锯割。用锯或刀将其两端的关节头截去，然后顺着骨体剖成粗细适用的长条。３、削锉。把劈裂后的骨条，用刀削去棱角，然后锉成圆锥状，制成骨笄的雏型。４、磨光。把具雏型的骨笄在砺石上打磨光滑。就是成品。５、雕嵌。有些骨笄磨光后，还在顶端雕镂纹饰，或者另外雕刻笄帽插装上去，有的在顶端还嵌有绿松石。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条