1) dimension of molten pool
熔池尺寸
1.
By means of an actual case,the dimension of molten pool was accurately calculated and the temperature profile and thermoisopleth in different sections and positions of welded joint were graphically expressed with the software Origin and Mathematica.
整个过程简单明了,没有数值计算的繁琐,可以为厚板焊接接头的温度场计算和焊缝熔池尺寸的计算提供快捷方法。
2) nugget size
熔核尺寸
1.
Regression model between nugget size and processing parameters;
熔核尺寸与点焊工艺参数的回归模型
2.
After transforming the spot welding DRC(Dynamic Resistance Curve)of stainless steel 1Cr18Ni9Ti by FFT(Fast Fourier Transform),the spectrum characteristics are analyzed and the nugget sizes of six spot welds are measured and contrasted.
1Hz处的幅频值随熔核尺寸变化的曲线斜率较小,0Hz处的幅频值随熔核尺寸的变化更为敏感。
3.
Aiming at the localization of traditional quality detection method during resistance spot welding, a new method is set up to detect the nugget size in real time.
本文针对传统点焊质量检验方法的局限性,提出了一种实时检测点焊熔核尺寸的新方法。
3) Droplet size
熔滴尺寸
1.
After the definition of molten droplet size in short-circuit transfer mode was given and the analysis system for molten droplet size and arc signals based on MATLAB platform was introduced,the characteristic of molten droplet size in short-circuit CO_2 arc welding using the power supply with constant voltage output,the relationsh.
建立了基于高速CCD摄像的熔滴图像检测和焊接电流、电弧电压同步采集系统,在给出短路过渡模式下的熔滴尺寸定义并简述基于MATLAB平台的熔滴尺寸与电弧信号分析系统的基础上,对平特性电源短路过渡CO2焊接熔滴尺寸变化特征及其与工艺性能间的关系进行了试验研究。
4) Pools sizes allocation
池尺寸分配
5) battery size
蓄电池尺寸
6) shape and size of droplet
熔滴形状和尺寸
1.
In this article,after the development actuality of droplet control in GMAW is introduced,a new idea to control the shape and size of droplet is brought forward.
在介绍熔化极气体保护电弧焊熔滴控制发展现状的基础上,提出了对熔滴形状和尺寸进行控制的新思想,并详细分析了其实现的关键技术和在现有技术条件下的实现途径。
补充资料：工程图标准尺寸及坐标尺寸
标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。
· 3.2 标准标注到坐标标注的转换
注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注：
- 被显示成线性尺寸的直径
- 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
- 选择作为参考基准线的尺寸
- 选择基准的引出线，该点为0点
- 选择 MOD DIM TYPE > Lin to Ord .
- 选择线性尺寸：注意：必须选择具有相同基准的尺寸
========>>>>
1. 选择 DIM PARAMS > Diam Dim Type .
2.点击Ord to Lin 
3.选择尺寸即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条