1) normal temperature drying
常温干燥
1.
In this paper, the 25 mm thickness Italian poplar thin board had been dried in the condition of comprehensive vapor drying technology with combination of high temperature drying and normal temperature drying technology in this experiment for more than one year.
应用高温干燥与常温干燥有机结合的工艺技术(简称蒸汽综合干燥法),对意杨25mm厚板材进行处理,在预热阶段进行充分的汽蒸处理,而后进入常压过热蒸汽干燥工艺阶段,当含水率降到25%时,转入常温干燥工艺阶段,直到干燥阶段结束。
2) Dry storage at room temperature
常温干燥贮藏
3) unheated air drier
常温气流干燥机
4) ambient pressure drying
常压干燥
1.
Preparation, Characterization and Properties of Silica Aerogel via Ambient Pressure Drying;
常压干燥制备SiO_2气凝胶及其结构、性能研究
2.
The thermal insulation material with ultra-low thermal conductivity made by using fiber felt to compound with SiO_2 aerogels and ambient pressure drying
纤维毡复合SiO_2气凝胶常压干燥法制备超低导热系数保温隔热材料
3.
Using industrial water glass as silica sources, SiO2 aerogels were synthesized via ambient pressure drying technique.
通过TMCS与水凝胶中孔隙水和表面-OH基团之间的反应,使对水凝胶的溶剂交换和表面改性在一步同时完成,在常压干燥条件下合成了SiO2气凝胶。
5) conventional drying
常规干燥
1.
Comparison of high-temperature drying and conventional drying of Chinese fir lumber;
人工林杉木高温干燥与常规干燥的比较研究
2.
Comparision of vacuum drying and conventional drying for poplar wood.
杨木真空与常规干燥的对比研究
3.
The small-diameter lumbers of Daimyo Oak(Quercus dentata) were dried with consecution-heat method and intermittent-heating methods(intermittent 2h and intermittent 6h) to study the occurred stress of surface layer of them during conventional drying process.
采用连续加热和间歇加热(间歇2h和间歇6h)方式对小径木锯材进行常规干燥,研究了干燥过程中小径木的表层应力(全应力和残余应力)发生、发展变化规律。
6) conventional drying
常压干燥
1.
The inorganic aerogel preparation through conventional drying and subcritical drying after solvent exchange or silation of the hydrogel is analyzed.
分析了无机气凝胶的溶剂置换常压和次临界干燥法制备以及硅烷基化处理常压干燥法制备,介绍了纤维增强气凝胶、多组分气凝胶和搀杂改性气凝胶。
2.
By controlling solution composition and surrounding conditions, the RF aerogel films with the thickness of micron-scale were successfully produced under conventional drying instead of supercritical drying.
以间苯二酚(Resorcinol)和甲醛(Formaldehyde)为前驱体,溶胶-凝胶法为主要方法,采用旋转涂膜,通过控制溶液配比及环境条件,用常压干燥方式取代通常的超临界干燥,成功制备出厚度在微米级的有机气凝胶薄膜。
补充资料：常温干燥
分子式：
CAS号：
性质：在常温条件下使涂膜干燥的工艺过程，也称自然干燥或空气干燥(air drying)。干燥时的气温、相对湿度和通风状况是影响干燥的重要因素。温度一般为10～35℃，相对湿度为75％以下，室内通风量为6～10次/h；室外风速在3级(3.4～5.5m/s)以下为宜。
CAS号：
性质：在常温条件下使涂膜干燥的工艺过程，也称自然干燥或空气干燥(air drying)。干燥时的气温、相对湿度和通风状况是影响干燥的重要因素。温度一般为10～35℃，相对湿度为75％以下，室内通风量为6～10次/h；室外风速在3级(3.4～5.5m/s)以下为宜。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条