1) phase separation
相分离法
1.
A new treatment process for titaniferous blast furnace slag at Pangang using phase separation was put forward.
提出采用相分离法处理攀钢高炉渣新工艺。
2.
In this thesis, using inorganic pigment (NLHN), ethyl cellulose (EC), cyclohexane (HC), Span-80 and poly-isobutylene (PIB) to prepare S/O type NLHN-RTM microcapsule by oil phase separation met.
本研究采用油相相分离法，以无机变色颜料NLHN为芯材，乙基纤维素(EC)为壳材，环己烷(HC)为溶剂，Span-80为乳化剂，聚异丁烯(PIB)为相稳定剂，制备了S／O型NLHN-RTM微胶囊。
3.
Using ethyl cellulose (EC), polyisobutylene (PIB) , cyclohexane (HC) and Span80 to prepare RTM/EC thermochromic microencapsule by oil phase separation method in which EC, PIB, HC and Span80 are used as shell material, phase stabilizer, solvent and emulsifier respectively.
研究以乙基纤维素(EC)为壳材料,聚异丁烯(PIB)为相稳定剂,环己烷(HC)为溶剂和Span80为乳化剂,采用油相相分离法制备了RTM/EC示温微胶囊。
2) phase separation method
相分离法
1.
The preparation methods for inorganic-organic composite particle such as mechanical mill method,heterogeneous coagulation method,phase separation method and monomer polymerization method are mainly introduced.
主要介绍无机-有机复合粒子制备方法——机械研磨法、异相凝集法、相分离法和单体聚合法。
2.
The encapsulation was conducted by using a phase separation method (PSM) and a solvent extraction method(SEM).
用具有生物降解性和血液相容性的聚乳酸 ( PLA)为载体材料 ,以牛血清白蛋白 ( BSA)为多肽 -蛋白质药物的模型化合物 ,分别用相分离法 ( PSM)和溶剂萃取法 ( SEM)制备出了平均粒径为 5 0～ 90 μm的 PLA/ BSA微球 。
3.
The development about tank stripping,tower stripping,direct drying method and phase separation method of cis-1,4-polybutadiene rubber solution were reviewed with 25 references.
简述了国内外顺丁橡胶溶液的釜式凝聚、塔式凝聚、直接干燥法和相分离法等的发展概况。
3) nanoprecipitation
相分离法
1.
Norcantharidin(NCTD) loaded PLA-PEG nanoparticles are prepared by double emulsion method and nanoprecipitation method respectively.
采用复乳法和相分离法两种方法制备去甲斑蝥素的聚乳酸-聚乙二醇嵌段共聚物(PLA-PEG)纳米微球。
4) wet phase separation
湿相分离法
1.
Study on the structure and performance of chitosan film prepared by wet phase separation;
湿相分离法壳聚糖膜的结构与性能研究
2.
The chitosan films prepared by wet phase separation was studied.
采用湿相分离法制备壳聚糖膜。
5) polymer two-phase partition
两相分离法
6) MPSM
复相分离法
1.
The feasibility and accuracy of MPSM to calculate the composition and volume fraction of these two phases were also demonstrated.
建立了用于计算γ′-Ni3Al和γ″-Ni3Nb成分及含量的最优化数学模型,证明了通过复相分离法(Multiple Phases Separation Method,以下简称MPSM)计算两相成分及含量的可行性和准确性,利用MPSM法计算了调整(Al+Ti)/Nb比值后析出相的成分、含量及分配量,解释了调整该比值对改型IN718合金高温稳定性影响的原因。
补充资料：相分离纺丝法
分子式：
分子量：
CAS号：
性质：一种特殊的纺丝方法。选用一种合适的在较高温度下能溶解聚合物的溶剂，配成纺丝溶液，当纺丝溶液从喷丝头压入纺丝甬道后，和冷空气相遇，发生“相分离”，析出纤维相而固化成丝。纺丝溶液的浓度范围与湿纺法相同，约10%~25%。此法能克服凝胶纺丝法存在的缺点，可用于聚乙烯醇、聚丙烯腈、聚乙烯、聚丙烯、聚氯乙烯纤维的生产。
分子量：
CAS号：
性质：一种特殊的纺丝方法。选用一种合适的在较高温度下能溶解聚合物的溶剂，配成纺丝溶液，当纺丝溶液从喷丝头压入纺丝甬道后，和冷空气相遇，发生“相分离”，析出纤维相而固化成丝。纺丝溶液的浓度范围与湿纺法相同，约10%~25%。此法能克服凝胶纺丝法存在的缺点，可用于聚乙烯醇、聚丙烯腈、聚乙烯、聚丙烯、聚氯乙烯纤维的生产。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条