1) streamline nozzle
![点击朗读](/dictall/images/read.gif)
流线形喷水孔
1.
A CFD technique is employed to simulate the formation of the water-jets discharged from streamline nozzles to investigate the effect of the nozzle geometries on dynamic characteristics of hydroentangling water-jets.
采用大型流体计算软件(CFD)模拟了高压水流流经流线形喷水孔形成动力水针的过程,以调查流线形喷水孔内部流道型线对水针动力特性的影响。
2) streamline nozzle
![点击朗读](/dictall/images/read.gif)
流线形喷嘴
3) spray finishing line
![点击朗读](/dictall/images/read.gif)
喷涂流水线
4) graphics pipeline
![点击朗读](/dictall/images/read.gif)
图形流水线
1.
Design and implementation of pixel processing back-end for 3D graphics pipeline;
![点击朗读](/dictall/images/read.gif)
3D图形流水线像素处理后期的设计和实现
2.
We proposed a graphics pipeline unit, namely Coarse-Z filter (CZF), for tile-level depth culling prior to per-pixel test, to reduce depth reading and thus reduce the pipeline bandwidth.
提出Coarse-Z Filter(CZF)图形流水单元,在像素级深度测试前进行Tile级深度测试,以减少读Z-Buffer的次数,从而有效地降低图形流水线的带宽·CZF提供单缓存和双缓存2种模式,前者由一个低分辨率过滤缓存组成,存储扫描转换后Tile内所有采样点的最大深度值;后者增加了一个辅助缓存和掩码位平面,以获得更高的剔除效率·测试结果表明,在当前渐趋复杂的场景中,使用CZF可降低30%~40%的带宽
5) internal flow of nozzle hole
![点击朗读](/dictall/images/read.gif)
喷孔内流
1.
The effects of injector structures on the internal flow of nozzle hole and characteristics of atomization near nozzle region were studied.
通过建立不同的计算边界研究了喷油器结构对喷孔内流及近喷孔区域燃油雾化特性的影响。
6) hydroentangling nozzle
![点击朗读](/dictall/images/read.gif)
喷水孔
1.
Simulation analysis of the effect of hydroentangling nozzle geometry on the breakup length of water-jets;
数值分析喷水孔结构对水针断裂长度的影响
补充资料:J形及L形密封
分子式:
CAS号:
性质:两种均为唇形橡胶密封,截面形状分别为J形和L形。多为纯橡胶制品,也有少数是夹布制品。根据使用条件,一般用天然橡胶或丁腈橡胶制造。结构较简单,摩擦力低,专用于气压或液压机械设备的活塞及活塞杆密封,工作压力在1MPa以下,如用于汽车和火车制动系统及离合器操纵系统中,起传递压力和密封的作用。
CAS号:
性质:两种均为唇形橡胶密封,截面形状分别为J形和L形。多为纯橡胶制品,也有少数是夹布制品。根据使用条件,一般用天然橡胶或丁腈橡胶制造。结构较简单,摩擦力低,专用于气压或液压机械设备的活塞及活塞杆密封,工作压力在1MPa以下,如用于汽车和火车制动系统及离合器操纵系统中,起传递压力和密封的作用。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条