1) Polyolefin-g-MAH
马来酸酐接枝聚烯烃
1.
Progress in Study of Polyolefin-g-MAH/Nylon Alloy;
马来酸酐接枝聚烯烃／尼龙共混合金的研究进展
2) PP-g-MAH
马来酸酐接枝聚丙烯
1.
To improve the interfacial compatibility between wood fiber and polypropylene as well as the toughness of wood fiber-polypropylene composites,maleic anhydride grafted polypropylene(PP-g-MAH) and maleic anhydride grafted styrene-ethylene-butadiene-styrene copolymer(SEBS-g-MAH) were used as modifiers.
为了改善木纤维与聚丙烯之间的界面相容性,提高木塑复合材的刚度和韧性,该文利用马来酸酐接枝聚丙烯(PP-g-MAH)及马来酸酐接枝苯乙烯-乙烯-丁二烯-苯乙烯嵌段共聚物(SEBS-g-MAH)对其进行增强和增韧改性。
2.
PA6/PP alloy was prepared using PP-g-MAH as compatilizer, and the effects of varied content of PP-g-MAH and PA6/PP ratio on alloy properties were studied.
以马来酸酐接枝聚丙烯(PP-g-MAH)为增容剂,制备了PA6/PP合金,研究了PA6/PP配比及PP-g-MAH用量对PA6/PP合金性能的影响。
3.
PP-g-MAH/down powder blend films with different content of powder were obtained after down powder were pretreated by different kinds of plasticizers,and the influence of down powder content,the type of PP,and the kind of plasticizers on the mechanical properties of blend films were studied.
采用不同增塑剂对羽绒粉体处理,制备了不同羽绒含量的马来酸酐接枝聚丙烯(PP-g-MAH)/羽绒粉体共混膜,分析了粉体含量、PP种类及不同增塑剂对共混膜力学性能的影响。
3) PE-g-MA
聚乙烯接枝马来酸酐
1.
PPS/PA66/epoxy resin blends and PPS/PE-g-MA/epoxy elastomer (E) blends were prepared by means of the reactive extrusion of PA66 with epoxy resin,PE-g-MA and epoxy elastomer respectively,the prepared blends had chemical cross-linked interface structure.
通过尼龙66(PA66)与环氧树脂、聚乙烯接枝马来酸酐(PE-g-MA)与环氧树脂类弹性体(E)的反应挤出,分别获得了具有微交联界面结构的PPS／PA66／环氧树脂共混体系和PPS／PE-g-MA／E共混体系,对共混物的损耗因数、力学性能及冲击断面形貌进行了研究。
4) maleic anhydride grafted polypropylene
马来酸酐接枝聚丙烯
1.
Influence of maleic anhydride grafted polypropylene on shear strength of adhesion bonded aluminum sheet/polypropylene/aluminum sheet;
马来酸酐接枝聚丙烯对铝薄板/聚丙烯界面粘接强度的影响
2.
Polypropylene (PP)/woodflour (WF) composites (WPC) was taken as research object to study the effects of content of woodflour and maleic anhydride grafted polypropylene (PP-g-MAH) on thermal properties of WPCs.
以聚丙烯(PP)/木粉(WF)复合材料(WPC)为对象,研究了WF及马来酸酐接枝聚丙烯(PP-g-MAH)含量对WPC热性能的影响。
3.
Wood powder converted into thermoplastic wood(TPW) though benzylated with phase transfer catalysis(PTC),which extruded and mixed into TPW/MAH-PP/Mica composite with maleic anhydride grafted polypropylene(MAH-PP) and Mica.
通过苄基化法在相转移催化剂(PTC)的作用下可将木粉制备成热塑化木材(TPW),然后将热塑化木材、马来酸酐接枝聚丙烯按一定比例配料后,再分别与不同质量的云母共混挤出,制备成热塑化木材/马来酸酐接枝聚丙烯/云母复合材料(TPW/MAH-PP/Mi-ca)。
6) PP-g-MAH
聚丙烯接枝马来酸酐
1.
Effect of PP-g-MAH on Mechanical Properties of PP/Attapulgite Composites;
聚丙烯接枝马来酸酐对聚丙烯/凹凸棒石复合体系力学性能的影响
2.
The compatibilization effect of PP-g-MAH on PP/PA6 blend was studied, and its effect on the mechanical properties of the blend was discussed.
研究聚丙烯接枝马来酸酐相容剂对聚丙烯／尼龙6体系的增容作用;并讨论了PP-g-MAH对PP／PA6共混物的力学性能的影响。
补充资料：顺酐接枝聚烯烃
分子式：
分子量：
CAS号：
性质：各种聚乙烯、聚丙烯、乙烯/乙酸乙烯共聚物与顺丁烯二酸酐接枝共聚所得的一类改性聚烯烃。其中顺酐的含量仅0.1%-0.5%(质量)，但能使聚烯烃的非极性得到改变，从而使聚烯烃具有粘接性、涂饰性、油墨印刷性等。这类改性聚烯烃可提高塑料的机械性能和耐热性。可用作挤塑复合膜的粘接层、钢管被覆层，也可用作聚烯烃与极性聚合物如尼龙等共混时的相容剂等。可在有机过氧化物存在下将熔融的聚烯烃与顺丁烯二酸酐进行接枝共聚而制成。
分子量：
CAS号：
性质：各种聚乙烯、聚丙烯、乙烯/乙酸乙烯共聚物与顺丁烯二酸酐接枝共聚所得的一类改性聚烯烃。其中顺酐的含量仅0.1%-0.5%(质量)，但能使聚烯烃的非极性得到改变，从而使聚烯烃具有粘接性、涂饰性、油墨印刷性等。这类改性聚烯烃可提高塑料的机械性能和耐热性。可用作挤塑复合膜的粘接层、钢管被覆层，也可用作聚烯烃与极性聚合物如尼龙等共混时的相容剂等。可在有机过氧化物存在下将熔融的聚烯烃与顺丁烯二酸酐进行接枝共聚而制成。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条