1) recovery rate
回复率
1.
The influences of aging heat treatment and thermomechanical training of shape memory effect(SME) on one-way recovery rate(ηs) and two-way recovery rate(ηt) of Ti50Ni50 shape memory alloy were studied.
研究了不同时效热处理和形状记忆效应训练(SME)对Ti50Ni50合金丝的单程形状回复率ηs、双程回复率ηt的影响。
2) recovery ratio
回复率
1.
The result showed that the treated wood had good dimension stability,and the moisture Absorption recovery ratio of thickness was 2.
结果表明:处理材的厚度吸湿回复率为2。
3) shape recovery rate
形状回复率
1.
Experiment results showed that after quenching and up-quenching heat treatment,the shape recovery rate of the alloys increased when the solid-solution temperature changed from 650 ℃ to 900 ℃,and reached the maximum value at 850 ℃.
结果表明,在650℃至900℃范围内,经淬火加沸水时效,合金的形状回复率随着固溶温度的升高而升高,在850℃左右达到最大值,并趋于平缓。
4) elastic recovery percentage
弹性回复率
1.
Study on elastic recovery percentage improvement of polyether ester elastic fiber with organic nucleating agent;
有机成核剂改善聚醚酯纤维弹性回复率的研究
2.
And it was found that these factors have no significant influence on the elastic recovery percentage of the floss silk,whereas the softener has significant influence.
通过碱液浓度、柔软剂浓度、超高温处理时间和柔软剂处理时间的正交试验设计,对相关指标进行DPS数据分析,发现4因素对丝绵的弹性回复率没有显著的影响,而柔软剂对弹性压缩率和含油率均有显著影响。
5) elastic recovery ratio
弹性回复率
1.
The relationship between their elastic recovery ratio and times by the resilient-elasticity recovery at constant elongation testing was analyzed.
对比分析了PTT长丝、PTT/氨纶、PA/氨纶、棉/氨纶包芯纱4种纱线的拉伸及回弹性能,通过定伸长反复拉伸实验,比较了各自弹性回复率随拉伸次数的变化关系。
2.
In this thesis,the properties involved elastic recovery ratio,curling tendency,shrinkage in boiling water of PTT were tested.
实验表明,PTT纤维具有优良的弹性回复率,PTT/PET、PTT/PBT纤维的卷曲性和沸水收缩性更为优异。
6) elastic recovery rate
弹性回复率
1.
Influence on the elastic recovery rate adding Re and Zr in the CuAlMnZn shape memory alloy;
添加Re及Zr对CuAlMnZn合金弹性回复率的影响
2.
This paper based on drape coefficient test,and gram test of seven common-used knitted fabrics and also tested tensile force,elastic recovery rate,the rate of plastic deformation,stress relaxation rate under conditions of tensile elongation.
以7种常用针织面料悬垂系数、面密度测试以及定伸长条件下拉伸力、弹性回复率、塑性变形率、应力松弛率的性能测试为基础,运用立体裁剪的方法试验得到零松量下针织原型各部位尺寸,通过灰色模型建模分析得出影响针织服装原型各部位尺寸的主要因素。
补充资料：卷曲回复率
分子式：
CAS号：
性质：卷曲纤维的伸直长度L与伸直后回复长度L1的差数对伸直长度L的百分率。计算公式为:。
CAS号：
性质：卷曲纤维的伸直长度L与伸直后回复长度L1的差数对伸直长度L的百分率。计算公式为:。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条