1) aromatic pore-forming agent
含苯环成孔剂
1.
An organic-inorganic hybrid macro-porous monolith material was prepared via Sol-Gel process incorporating polymeric component of a new aromatic pore-forming agent with silicon glass.
以自行设计并合成的含苯环成孔剂为有机相,正硅酸乙酯为无机相,基于溶胶-凝胶方法,制备了有机/无机两相间以共价键结合的杂化大孔材料。
2) Pore-forming agent
成孔剂
1.
Effect of pore-forming agent on properties of Al_2O_3 supports;
成孔剂对氧化铝支撑体性能的影响
2.
The effect of the pore-forming agent content and silicon powders size on the dielectric and mechanical properties of RBSN ceramics were investigated.
以硅粉为原料,通过添加不同含量的成孔剂,反应烧结制备出具有不同气孔率的低密度多孔氮化硅陶瓷,研究了成孔剂含量和硅粉粒度对反应烧结氮化硅性能的影响。
3.
6,were fabricated using two different preparation routes:(i) the addition of pore-forming agent,and(ii) freeze-drying processing.
采用添加成孔剂和冰冻-干燥法制备了具有不同气孔率的氮化硅多孔陶瓷,研究了该陶瓷在9。
3) pore-forming material
成孔剂
1.
The influence of organism PVA as pore-forming material and adhesive on the properties of alumina support are studied in this paper.
以α-A l2O3粉末为骨料,以聚乙烯醇(PVA)作粘接剂和成孔剂,采用塑性挤压成型技术和固态粒子烧结法制备氧化铝多孔陶瓷支撑体。
4) pore-forming agents
成孔剂
1.
Effect of the content of pore-forming agents on properties of macroporous alumina supports;
成孔剂的量对多孔氧化铝支撑体孔结构的影响
5) pore-forming additives
成孔剂
1.
Alumina-based porous ceramic filter elements for hot gas are prepared by adding pore-forming additives and combining casting and gel-casting progresses.
以氧化铝为基体材料,采用添加成孔剂法,并结合注浆成型和凝胶注模成型制备出用于过滤高温煤气的陶瓷过滤元件。
2.
Results show that the granularity of the aggregate determines the size and distribution of pores and then the granularity of pore-forming additives and the thickness of desulfurizer film also have some influence on these parameters.
研究结果表明,骨料粒度是决定气孔参数的主要因素,其次是成孔剂粒度及脱硫剂膜层厚度。
6) blowing agent
成孔剂
1.
The density of foam decreased and its porosity increased as the blowing agent level in the foam increased.
采用溶析成孔技术制备的硅橡胶泡沫材料，随着成孔剂用量增大，其密度减小，孔隙度提高。
补充资料：苯环
苯分子所具有的结构。为平面的正六边形，每个键角均为120°，碳碳间的键长均为140×10-10米。碳碳间的键为介于单键和双键间的独特键。芳香族化合物中一般均含有一至多个苯环。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条