1) HR-2 steel
HR-2钢
1.
Diffusion bonding processes and its joint properties of aluminum-silicon(Al-Si)alloy to HR-2 steel by hot isostatic pressing were studied in this paper.
采用热等静压直接扩散连接方法对Al-Si合金/HR-2钢进行了研究。
2) HR 2 stainless steel
HR-2不锈钢
1.
In the electroplating process,aluminum deposition from AlCl_3/EMIC to the surface of HR 2 stainless steel was performed with a deposition rate of 15μm/h at 25℃under the protection of argon gas.
为避免制备温度过高引起基体性能退化,采用了室温熔盐电镀与热处理复合技术在HR-2不锈钢上进行了渗Al涂层制备研究,并对涂层的形貌、结构和成分进行了表征。
3) HR-2 stainless steel
HR-2抗氢不锈钢
4) HR-2 alloy
HR-2合金
1.
The multiscale simulations of the effect of helium and dislocation on the mechanical properties of HR-2 alloy are carried out in this paper.
本文开展了氦和位错对HR-2合金力学性能影响的多尺度模拟研究。
5) HR-1 stainless steel
HR-1不锈钢
1.
Cu is used as the mesosphere material in the experiment, and the diffusion-bonding experiment of Be/Cu/HR-1 stainless steel is made on the Greeble1500 hot stimulation test-machine.
以Cu为中间层材料,采用Greeble1500热模拟试验机对Be/HR-1不锈钢进行扩散连接试验,利用PMEOlympusTokyo光学显微镜、扫描电镜(SEM)、显微硬度计(HV-1000)、X射线衍射仪研究分析了其界面特性。
6) HR-2 thermal infrared imager
HR-2型红外热像仪
1.
Through comparing the calculated results with the experimental data,which is achieved with the HR-2 thermal infrared imager from the end face and the side face of the Nd:GGG crystal,valuable conclusions are obtained.
考虑温度大幅度变化对工作介质比热容的影响,在激光二极管阵列峰值抽运功率超过10~4W 的情况下,对热容激光器片状18mm×18mm×10mm Nd：GGG 工作介质进行了温度分布的数值计算,并与 HR-2型红外热像仪对工作介质端面与侧面测量的温度数据进行了对比分析,取得了一些有价值的结果。
补充资料：Permanent Yellow HR
分子式：
CAS号：
性质：黄色粉末。着色物呈红光黄色。熔点380～420℃。密度l.27～1.50g/cm3。具有优良的耐热、耐溶剂及耐迁移性能。3,3′-二氯联苯胺的重氮盐与色酚AS-IRC,(4-氯-2,5-二甲氧基乙酰乙酰苯胺)偶合制得。用于高档印刷油墨、油漆、塑料的着色及涂料印花。
CAS号：
性质：黄色粉末。着色物呈红光黄色。熔点380～420℃。密度l.27～1.50g/cm3。具有优良的耐热、耐溶剂及耐迁移性能。3,3′-二氯联苯胺的重氮盐与色酚AS-IRC,(4-氯-2,5-二甲氧基乙酰乙酰苯胺)偶合制得。用于高档印刷油墨、油漆、塑料的着色及涂料印花。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条