1) intake system
进气系统
1.
Numerical simulation of flow field in intake system in internal combustion engine with tangent intake duct;
切向进气道内燃机进气系统流场的数值模拟
2.
The Improvement Design of the 495QME Gasoline Engine Intake System Basing on CFD;
基于CFD的495QME汽油机进气系统改进设计
3.
The paper optimizes the intake system of a car by the method of combination of CAE and test.
用CAE仿真计算和实验验证相结合的方法,对轻型汽车的进气系统进行声学优化,通过优化,将该车的通过噪声降低2dB(A),从而使其达到法规的要求。
2) inlet system
进气系统
1.
The numerical simulation and model test of the inlet system for a hovercraft gas turbine are conducted,and the results show that the inlet system can meet completely the requirements of the inlet flowfield uniformity.
进行了气垫船用燃气轮机进气系统数值模拟计算及模型试验研究,结果表明所设计的进气系统完全能满足进气流场的均匀性要求。
2.
The structure and the aerodynamics performance of gas turbine inlet system is one of the important aspects when the gas turbine is installed on the naval vessels.
燃气轮机进气系统的结构和气动性能是燃气轮机装舰技术研究的一个重要组成部分。
3.
The inlet system of 6102 gasoline engine is simultaed by means of un-steady flow program.
应用波动循环模拟程序对6102汽油机的进气系统进行了模拟计算。
3) air intake system
进气系统
1.
Design of air intake system for SDD_(1A) locomotive;
SDD_(1A)型机车进气系统的设计
2.
An air intake system design is analyzed using this method, especially a layout of the air filter in a bus and air intake tube design to obtain corresponding design rules and design hard points and provide thoughts and theoretical basis for optimization of the air intake system design.
介绍功能主义设计和设计硬点的思想,提出以功能驱动的硬点结构设计方法,并通过此方法对进气系统的结构设计进行分析。
3.
This paper describes the methods and steps of testing and diagnosing the troubles of the engine air intake system using on－ board self diagnosis system.
介绍了用随车故障自诊断系统检测诊断发动机进气系统故障的方法和步骤。
4) induction system
进气系统
1.
In this paper, the authors present an improved scheme of the induction system of the EQ6100 gasoline.
将 EQ6 1 0 0 Q型汽油机原进气系统改进为可变进气系统。
5) intake and exhaust system
进排气系统
1.
A research on the engine performance at full load, firing pressure in cylinder, pressure fluctuation in intake and exhaust system, pressure of muffler outlet was made using this model.
基于GT-POWER软件建立了包括增压柴油机进气系统、排气系统和排气消声器的工作过程模拟计算模型,通过模拟计算研究了发动机的外特性指标、最高燃烧压力、进排气系统压力波动、消声器端口压力等参数的变化,试验验证表明:所建立模型能够正确预测发动机进排气系统中的压力波。
2.
The objective of this thesis is to study intake and exhaust system of turbocharged diesel engine and matching between each component by theoretical and simulation methodology.
本文采用理论分析和仿真分析相结合的方法,对某型增压柴油机的进排气系统以及各部件之间的匹配进行了较为详细、深入的研究。
3.
The analysis methods of acoustic insulation performance for intake and exhaust system were summarized.
总结了进排气系统隔声性能分析方法,对比了混响室法和阻抗管法测量隔声性能的适用范围,指出测量过程中产生误差的主要原因,为隔声性能测量方法的选择提供依据;同时,指出一维解析法和三维数值法都可用来分析消声器的传递损失,一维方法的使用受制于结构形状以及截止频率,三维数值方法更为实用,总结了穿孔板、吸声材料等关键部分的模拟方法,指出了目前仿真分析中存在的问题。
6) Intake/Exhaust system
进/排气系统
补充资料：进气法
进气法
进气法 针灸学名词。指针刺手法。《金针赋》：“进气之诀，腰背肘膝痛，浑身走注疼，刺九分，行九针，卧针五七吸，待气上下。”《针灸大成》称作“运气法”：“凡用针之时，先行纯阴之数，若觉针下气满，便倒其针，令患人吸气五口，使针力至病所。此乃运气之法，可治疼痛之病。”意指先直刺，行紧提慢按六数，得气后，将针斜对病痛处，行气后，让吸气五、七口，以助运气。用于各种痛症。《针灸问对》：“针入天部，行九阳之数，气至，速卧倒针，候其气行，令病人吸气五、七口，其针气上行，此乃进气之法，可治肘臂、腰脚、身疼。”
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条