1) alloy coating
合金涂层
1.
Based on the technology of Co-B and Co-P alloys nanocrystalline coatings, the ternary Co-Ni-B and Co-Ni-P nanocrystalline alloy coatings were obtained, and the deposit rate and microstructure of ternary nanocrystalline alloys were investigated.
在化学沉积钴硼、钴磷合金纳米晶涂层制备工艺的基础上,制备了钴镍硼、钴镍磷纳米晶合金涂层,研究了三元纳米晶合金的沉积速率和显微组织结构。
2.
Results showed that satisfactory alloyed layer could be also formed on steel castings without adding fusing agent into alloy coating.
研究表明,合金涂层中不加熔剂也能形成质量较好的合金层;铸型中合金膏块相对厚度是决定铸件表面合金层厚度的主要因素;浇注温度提高,合金颗粒适当增大,有利于增加合金层厚度;铸钢合金层的耐激冷激热性能好。
3.
The Ni-based alloy coating and Ni-clad WC ceramic coating were prepared and characterized by abrasive wear resistance test.
对镍基合金涂层和Ni/WC陶瓷涂层进行耐磨实验,结果表明:两种涂层存在不同的磨损特性,WC陶瓷颗粒在涂层及其表面的均匀分布可提高涂层的耐磨性,硬度和韧性的相互匹配是提高材料耐磨性的有效方法。
2) pseudo alloy coating
伪合金涂层
1.
The result shows that compared with pseudo alloy coatings,low-carbon martensite coating presents superior mechanical,anti-wear and machining properties which can be applied to engine components remanufacturing like crankshaft etc.
实验结果表明,与伪合金涂层相比,低碳马氏体涂层呈现出更优异的力学性能、耐磨性能和机械加工性能。
2.
Effects of heat treatments on structure and properties of Mg-A1 Pseudo Alloy Coatings were studied.
本文采用电弧喷涂技术在6061铝合金基材表面制备纯铝涂层,并采用环氧树脂封孔;采用镁铝异质丝材电弧喷涂制备了四种不同镁含量的Mg-Al伪合金涂层,并对涂层进行热处理和环氧树脂封孔。
3) NiCrBSi alloy coating
NiCrBSi合金涂层
1.
In virtue of electron energy spectrometer, X-ray diffractometer and scanning electron microscope, the effects of rare earth yttrium on chemical composition and structure of the vacuum fusion sintering NiCrBSi alloy coating were studied.
利用电子能谱仪、X射线衍射仪、扫描电子显微镜等研究了稀土Y对真空熔结NiCrBSi合金涂层化学组成和组织结构的影响。
4) 316L alloy coating
316L合金涂层
1.
A 316L alloy coating was prepared by high velocity oxygen fuel thermal spraying technique (HVOF) on A3 carbon steel.
利用超音速热喷涂技术在碳钢基体上制备出了 316L合金涂层 ,研究了该涂层在实际炼油环境中的冲蚀行为。
6) NiCrWTi alloy film
NiCrWTi合金涂层
补充资料：氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
J氟碳涂层铝合金装饰板制成的铝合金幕墙建筑物
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条