1) eccentric effect
偏心影响
1.
Aiming at the envi- ronmental factors of eccentric effect for LWD density logging,three kinds of interval correction models of circle,ellipse and trough are es- tablished to realize the eccentric effect correction.
本文针对随钻密度测井受偏心等环境因素的影响,建立了圆形、椭圆形和槽型三种间隙校正模型,进而实现随钻密度测井资料的偏心影响校正。
2) eccentric influence factor
偏心影响系数
1.
The eccentric influence factor α in the present tunnel specifications is used to express the extent of decreasing of compression strength of the eccentric loading plain concrete element in accordance with the increasing of the eccentric distances .
现行隧道设计规范用偏心影响系数α表征偏压构件抗压强度随偏心距增加而降低的程度，引入可靠度设计时必须知道此系数的统计特征及计算公式的不确定性。
3) Deviation influence
偏差影响
4) psychological effects
心理影响
1.
It presents the deficiencies caused by the ambiguity and confusion of the semiotic characteristics of uniforms;it expounds and proves the psychological effects of uniforms on people a.
指出制服的符号特征模糊混淆带来的弊端 ,论证了制服对穿着者的心理影响 ,以及制服形象的社会效应 ,对我国制服改革与国际接轨作出了评价和分析。
2.
Objective: To investigate relevant condition of informed consent of inpatients and patients’psychological condition before informed consent and after informed consent, and to explore the psychological effects of informed consent to different conditions’patients.
目的: 在了解住院患者知情同意相关情况及知情同意前、后心理状况的基础上,探讨知情同意对不同病情住院患者的心理影响。
5) Psychological effect
心理影响
1.
The study intended to find the differences of the psychological effects of green paper and traditional white paper on students.
本研究试图探明绿色书写纸与传统的白色书写纸对学生书写时心理影响的差异。
2.
This research takes electroencephalogram as the evaluation index of psychological effect to reflect the quantity of human body s emotion objectively, and tries a new way to study the relation between environment and human beings.
本研究以脑波变化作为心理影响的评价指标,客观量化地反映人体的情绪感受,尝试人与环境之间关系研究的新方法。
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条