1) composite coating
复合刷镀层
1.
A pure nickel coating and n-Al2O3/Ni composite coating were prepared.
制备了纯镍刷镀层和镍基纳米氧化铝复合刷镀层。
2.
To research the wear mechanics of nano-particle composite coating in lubricated condition with sand in oil,a nickel matrix nano-Al_2O_3 composite coating was prepared.
为研究纳米颗粒复合电刷镀层在含沙粒油润滑条件下的磨损机制,首先制备了镍基纳米A l2O3复合电刷镀层,采用T-11球盘式磨损试验机进行复合刷镀层在含沙粒油润滑条件下的磨损试验,采用FTP-X2型分析式铁谱仪对复合镀层磨损试验后的润滑油中的磨粒形貌进行了研究。
2) composite electro-brush coating
复合电刷镀层
3) Ni-based composite coating
镍基复合刷镀层
4) composite brush plating
复合刷镀
1.
The impact of anion surfactant SDS,cation surfactant PEI,non-ionic surfactant OP added in the composite brush plating bath on the dispersity of nano-WC is investigated.
研究了在(Ni-P)-纳米WC复合刷镀液中添加阴离子型表面活性剂SDS、阳离子型表面活性剂PEI、非离子型表面活性剂OP对分散体系分散效果的影响。
2.
Effects of polyethyleneimine(PEI) surfactant on the dispersibility of nanometer Si3N4 in the(Ni-P)-nanometer Si3N4 composite brush plating solution and on the structure and properties of the coating of(Ni-P)-nanometer Si3N4 composite brush plating were studied.
研究了聚乙烯亚胺对刷镀(Ni-P)-Si3N4纳米微粒复合镀液中Si3N4纳米微粒的分散性、刷镀层性能及结构的影响,并确定了聚乙烯亚胺在复合刷镀液中的最佳含量。
3.
Ni P) nanometer Si 3N 4 composite brush plating technology, and the equipments, the plating solution composition, the method of the solution's making up thereof are discussed.
论述了 ( Ni- P) -纳米 Si3N4 微粒复合刷镀工艺、设备及 ( Ni- P) -纳米 Si3N4 微粒复合刷镀液的组成和配制方法 ;研究了纳米 Si3N4 微粒在刷镀液中的含量、刷镀工作电压和刷镀温度对 ( Ni- P) -纳米 Si3N4 微粒复合刷镀层的影响 ;研究了在不同的热处理温度下复合刷镀层的硬度和耐磨
5) n-Al_2O_3/Ni composite plating
n-Al2O3/Ni复合刷镀层
6) brush composite plating
复合电刷镀
1.
This paper analyses some factors that influence the brush composite plating Ni-Fe-diamond technology, including temperature?voltage and relative velocity, and acquires optimal technical parameter of high content and high wear.
文章通过对镍铁-金刚石复合电刷镀工艺中温度、电压和相对速度的试验研究,获得了高的金刚石含量和高耐磨性的最佳工艺参数。
2.
This Paper analyses all factors that influence the codeposition of sic particles, and shows the mathematical model of strong adsorption one way theory of brush composite plating by analyses the two-step adsorption theory and brush composite plating technigue.
分析了影响SiC微粒共沉积的各种因素,并通过对两步吸附理论和复合电刷镀工艺的分析,提出复合电刷镀的强吸附单途径理论的数学模型,从而对实际试验结果作出了理论解释。
补充资料：刷腻
1.擦抹油脂。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条