1) bearing
[英]['bɛəriŋ，'beərɪŋ] [美]['bɛrɪŋ]
轴瓦
1.
Research on coated part peeling off at the bearing on connecting bar s big end in the introduced marine diesel engine;
某型引进船用柴油机连杆大端轴瓦镀层剥落研究
2.
Rebuild of DH80 - 7 air compressor bearing;
DH80-7空压机轴瓦改造
3.
Analysis for Ling’ao Nuclear Power Station unit 1 exciter No.11 bearing white metal damage and its operating temperature abnormal high;
岭澳核电站1号机组励磁机11号轴瓦乌金损坏及运行温度高的原因分析
2) bearing bush
轴瓦
1.
Rescrape of bearing bush for DA120 centrifugal compressor and its axial spotting;
DA120离心式压缩机轴瓦刮研及轴找正方法
2.
Research and development of domestic new product JZZ for automobile bearing bush;
汽车轴瓦用国产化新材料JZZ的研制
3.
Design and implementation for a new bearing bush measurement system based on single-chip microcomputer;
一种车用轴瓦自动检测装置的设计与实现
3) bush
[英][bʊʃ] [美][buʃ]
轴瓦
1.
Discussion on technology of repairing truncation three oil wedges bush of 200MW turbine;
200MW汽轮机平切三油楔轴瓦修复技术探讨
2.
The worn surface of an Al-Sn alloy bush got from a locomotive engine after using the mineral additive was analyzed.
利用销盘式磨损试验机研究了一种矿物质润滑油添加剂对钢/铝锡合金摩擦副摩擦学性能的影响,并考察了这种添加剂对实际工况下铝锡合金轴瓦的作用效果。
3.
ammonia pump and its main parame-ters,analyzes the reasons for such respects as trip at low electric charge,leakage of mechanical seal,shaft vibration and displacing upward as well as the motor's bush being burnt,and puts forward somesolutions.
介绍离心式高压氨泵的密封和主要参数，分析使用过程中出现的低电负荷跳车、机封泄漏、轴振动和轴位移高、电机轴瓦烧坏的原因，并提出了解决对策，对尚存在和正在改进的问题作了介绍。
4) bearing shell
轴瓦
1.
Running-in wear simulation test for crankshaft journal-bearing shell of S50MC marine diesel engine
S50MC船用柴油机曲轴颈-轴瓦磨合磨损的模拟试验研究
2.
Through check and test,cause is found which brings to bearing shell temperature of feed water pump electromotor going up,and effective settlements are adoped to make operation effects to get the best state.
通过检查和试验,找出了导致某电厂给水泵电动机轴瓦温度升高现象的原因,并采取了有效的解决方案,使运行效果达到最佳状况。
3.
The paper discusses that the two typical bearing shell defect s analyses treatment in general repair on barrel-shaped steel ball mill;influencing the bearing shell motivity lubricate s safety factor;bearing shell oil film s safety operating condition is reduced by year after year,and must carry on restoring work to peak barrel bearing shell in 8-10 years.
对轴瓦膨胀间隙减少缺陷进行了分析,提出了预控措施和一套合理的现场处理方法。
5) bearing liner
轴瓦
1.
The overhigh temperature early warning and auto - stop - working protect system for bearing liner of pulverizer;
球磨机主轴轴瓦超温预警与自动停车保护系统
2.
The method of reducing failure rate for measuring bearing liner temperature in DAS system of 300MW turbine set;
降低300MW汽轮机组DAS系统轴瓦温度测点故障率
3.
The technology of N-95cleaning fluid with DJ specific additive special for bearing liner production line is introduced.
介绍了以DJ为特效添加剂的N-95型专用于轴瓦生产流水线的清洗液的工艺特点。
6) Wafangdian bearing
瓦轴
1.
Through the designing summary of Wafangdian bearing group industrial garden,it discusses the modernized industrial garden concept based on gardenization,humanity and high-technologization of modern industrial construction.
通过瓦轴工业园的设计总结,探讨了现代工业建筑的园林化、人性化、高科技化的现代化工厂理念,并为工业建筑的设计和规划提供了参考借鉴。
补充资料：轴瓦合金
分子式：
CAS号：
性质：又称轴瓦合金。用于制造滑动轴承的材料。轴承合金的组织是在软相基体上均匀分布着硬相质点，或硬相基体上均匀分布着软相质点。轴承合金应具有如下性能：良好的耐磨性能和减磨性能；有一定的抗压强度和硬度，有足够的疲劳强度和承载能力；塑性和冲击韧性良好；具有良好的抗咬合性；良好的顺应性；好的嵌镶性；要有良好的导热性、耐蚀性和小的热膨胀系数。用于各类轴承材料。
CAS号：
性质：又称轴瓦合金。用于制造滑动轴承的材料。轴承合金的组织是在软相基体上均匀分布着硬相质点，或硬相基体上均匀分布着软相质点。轴承合金应具有如下性能：良好的耐磨性能和减磨性能；有一定的抗压强度和硬度，有足够的疲劳强度和承载能力；塑性和冲击韧性良好；具有良好的抗咬合性；良好的顺应性；好的嵌镶性；要有良好的导热性、耐蚀性和小的热膨胀系数。用于各类轴承材料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条