1) flat roll
平辊
1.
A series of flexible U sections,changed in its sections,was separately simulated and analyzed by edger roll forming and flat roll forming.
本文对变截面辊弯成型仿真采用轧辊轴向加工技术(代替法向加工技术),对角度连续变化的变截面U型材分别进行立辊加工和平辊加工成型模拟分析。
2.
As for flat roll of F4～F6 stands,their pre-grinding crowns were optimized and the flatness of strips was greatly improved.
采用五次曲线分析了某厂热轧精轧机组F1~F3机架CVC轧辊辊型系数确定方法,对比了三种辊型曲线的区别,推导了等效凸度与窜辊量间的三次函数关系;对F4~F6机架平辊的预磨凸度进行优选,明显改善了带钢的平直度。
3.
If the CVC work roll on the F7 stand of Baosteel 2050 mm hot strip rolling mill is substituted by flat roll (for schedule-free rolling, SFR) and the strip profile is controlled by the existing bending force, the control will be inadequate.
通过现场实验的方法证明了国内某钢厂 2 0 5 0 mm热轧机组精轧 F7工作辊由 CVC改为平辊 ,(目的是实施自由程序轧制 )单靠现有弯辊能力对板凸度控制的不足 ,并提出采用大凸度支承辊提高板凸度控制能力的方案。
2) flat rolling
平辊轧制
1.
Lateral spreading deformation behavior in flat rolling of copper cladding aluminum composite rods
铜包铝复合棒材平辊轧制宽展变形行为
2.
Deformation during flat rolling is dissussed.
提出了用上限法分析稳态塑性变形问题的一般方法，用双流超几何函数法导出了通用的运行许可速度场的数学表达式，并对平辊轧制问题进行了讨论
3.
The deformation behaviour of copper cladding aluminum wire in flat rolling process was investigated.
采用三维刚塑性有限元法,研究铜包铝复合线材由圆断面到扁断面的平辊轧制变形行为及其对主要工艺参数的影响,并对模拟结果进行实验验证。
3) V rolling
平辊立轧
1.
Based on physical simulation of edge rolling process in Trimming-Free Plate rolling method,the effection of V rolling and chamfer rolling on the plate profile is analyzed.
基于中厚板无切边轧制法中立轧轧边变形的物理模拟,分析了平辊立轧与倒棱轧制对中厚板断面形状的影响。
2.
Based on physical simulation of edge rolling process,the article analyzed the effection of V rolling and chamfer rolling on the plate profile.
基于中厚板在立轧轧边后板坯变形的物理模拟,分析了平辊立轧与倒棱轧制对中厚板断面形状的影响。
4) roll smoothing progress
辊式校平
1.
The experimental and simulated results show that the relative accurate results could be obtained when the roll smoothing progresses are resolved as a plane strain problem.
用实验和数值模拟相结合的方法,研究了辊式校平过程对10Ni5CrMoV钢大尺寸船用板材残余应力的影响规律。
5) skin pass roll
平整辊
1.
The heat treatment process parameter for φ2 800 mm skin pass roll with Cr5 material has been researched and applied into the practical production,so that the secondary hardening skin pass roll used for cold rolling has been successfully manufactured.
对Cr5材料φ2 800 mm冷轧平整辊热处理工艺参数进行了研究并应用于实际生产,成功制造出二次硬化冷轧用平整辊。
6) ironing roll
熨平辊
1.
Solutions for stability of ironing roll for high speed foil mill;
铝箔轧机高速运行时熨平辊稳定性的解决
2.
The test in-troduces the characteristic of ironing roll deisgn and application of high speed aluminum strip mill.
本文介绍了熨平辊设计的特点和在高速铝带轧机上的应用。
补充资料：辊辊
1.犹混混。形容苟且混世。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条