1) thermoplastic vulcanizate
热塑性硫化胶
1.
Foamed ethylene-propylene-diene rubber/polypropylene thermoplastic vulcanizate prepared by chemical foaming Ⅰ. Extrusion processing parameters;
化学发泡法制备发泡三元乙丙橡胶/聚丙烯热塑性硫化胶 Ⅰ.挤出工艺参数
2.
Properties of intumescent flame retardant ethylene propylene diene monomer/polypropylene thermoplastic vulcanizate;
膨胀阻燃三元乙丙橡胶/聚丙烯热塑性硫化胶的性能
3.
NBR/PP thermoplastic vulcanizates compatibilized by ATBN/MP;
ATBN/MP复合增容NBR/PP热塑性硫化胶
2) TPV
热塑性硫化胶
1.
Preparation and properties of RIIR/PP TPV
IIR再生胶/PP热塑性硫化胶的制备与性能研究
2.
The effects of the preparation and the addition level of flame retarder on the properties of flame retardant EPDM/PP TPV were investigated.
研究制备工艺和阻燃剂用量对EPDM/PP阻燃热塑性硫化胶(TPV)性能的影响。
3.
The effect of the primary flame retardant magnesium hydroxide [Mg(OH)_2] combined with decabromo diphenylethane(DBDPE)/antimonous oxide(Sb_2O_3)/ingredient A——a polymerized organo-silicone on the properties of EPDM/PP TPV was investigated.
采用氢氧化镁为主阻燃剂,配合使用十溴二苯乙烷(DBDPE)、三氧化二锑和配合剂A(一种有机硅高分子材料),研究四者对EPDM/PP热塑性硫化胶(EPDM/PPTPV)性能的影响。
3) thermoplastic vulcanizate
热塑性硫化橡胶
1.
Effect of plasticizers on acrylonitrile-butadiene rubber/polypropylene thermoplastic vulcanizate;
增塑剂对丁腈橡胶/聚丙烯热塑性硫化橡胶性能的影响
2.
Preparation and properties of thermoplastic vulcanizates;
热塑性硫化橡胶的制备与性能
4) thermoplastic dynamic vulcanizate
热塑性动态硫化橡胶
1.
The effects of rubber phase crosslinking density and average rubber particle diameter on mechanical and rheological properties of low hardness EPDM/PP blend thermoplastic dynamic vulcanizates(EP－TPV) prepared by reactive extrusion dynamic vulcanization were studied.
研究了反应挤出型低硬度EPDM/PP共混型热塑性动态硫化橡胶（EP－TPV）胶相交联密度和平均胶相粒径对力学性能和流变性能的影响。
5) thermoplastic dynamic vulcanizates
热塑性动态硫化胶
1.
Low hardness EPDM/polypropylene thermoplastic dynamic vulcanizates Ⅰ. Preparation technology by a twin-screw extruder;
低硬度EPDM/PP热塑性动态硫化胶Ⅰ.用双螺杆挤出机的制备工艺
2.
The development history of preparation technology of reactive extrusion dynamic vulcanization for thermoplastic dynamic vulcanizates was introduced,and reactive extrusion dynamic vulcanization technology,including its characteristics,preparation technology conditions,vulcanization rate and vulcanization process,was systematically discussed.
介绍了制备热塑性动态硫化胶的反应挤出动态硫化技术的发展历史 ,系统论述了该技术的特点、工艺条件、硫化速率及硫化过程。
补充资料：热塑性硫化胶
分子式：
分子量：
CAS号：
性质：橡胶与热塑性聚烯烃中加入硫化剂经动态全硫化制得的热塑性弹性体（TPE）。典型的品种有：丁腈橡胶/聚丙烯/增容剂耐油热塑性硫化胶，丁腈橡胶/聚酰胺/增容剂热塑性硫化胶等。由于橡胶微粒（1~5微米）在常温和加工温度下均保持网状结构并显示弹性，热塑性和强度由聚烯烃（或线型聚酰胺）提供，故其强度、弹性和耐热性均优于动态部分硫化的热塑性聚烯烃。其用途可参见热塑性橡胶。
分子量：
CAS号：
性质：橡胶与热塑性聚烯烃中加入硫化剂经动态全硫化制得的热塑性弹性体（TPE）。典型的品种有：丁腈橡胶/聚丙烯/增容剂耐油热塑性硫化胶，丁腈橡胶/聚酰胺/增容剂热塑性硫化胶等。由于橡胶微粒（1~5微米）在常温和加工温度下均保持网状结构并显示弹性，热塑性和强度由聚烯烃（或线型聚酰胺）提供，故其强度、弹性和耐热性均优于动态部分硫化的热塑性聚烯烃。其用途可参见热塑性橡胶。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条