1) wide slab continuous casting
宽板坯连铸
1.
Based on the150 mm×(1 600～3 250) mm wide slab caster mold as investigating object,the level fluctuation in the mold of the wide slab continuous casting was simulated by a three dimensional finite-volume model(VOF) which had been formulated according to the commercial code ANSYS CFX10.
以150 mm×(1600~3 250)mm宽板坯连铸结晶器为研究对象,利用大型商业软件ANSYS CFX10。
2.
Based on four sectional width of wide slab continuous casting mold of a steelmaking plant in China,a water model with 1∶1 ratio was established,and according to the orthogonal test method,the influence of the different factors on the flow in the mold was studied,including hole numbers of SEN,argon gas injection of nozzle,immersion depth of nozzle,casting speed and sectional size of mold.
结合国内某钢厂宽板坯连铸结晶器的4种断面宽度,建立1∶1水模型,并结合正交试验方法,研究了浸入式水口的吐出孔数、水口吹气量、水口浸入深度、拉速和结晶器断面宽度等不同因素对结晶器流场的影响,得到了4种宽板坯连铸结晶器的最佳工况条件。
2) wide slab caster
宽板坯连铸
1.
Water model experiments on surface flow fluctuation patterns in wide slab caster mold;
宽板坯连铸结晶器内液面波动的水模型研究
2.
Taking 150 mm×1 600～3 250 mm wide slab caster mold as an investigating object,the fluid flow in the mold of wide slab continuous casting is simulated by a three dimensional finite-volume model,which has been formulated according to the commercial code ANSYS CFX10.
以150 mm×1 600~3 250 mm宽板坯连铸结晶器为研究对象,利用大型商业软件ANSYSCFX10。
3) wide and thick slab continuous casting
宽厚板坯连铸
1.
A water model of a wide and thick slab continuous casting tundish was established to study the effect of different control devices on the characteristics of fluid flow.
通过宽厚板坯连铸中间包水模实验,研究了不同控流装置对中间包内流动特性的影响。
4) slab continuous casting
板坯连铸
1.
Research and development of secondary cooling heat transfer model for Baosteel 1930 mm slab continuous casting;
宝钢1930mm板坯连铸二冷传热模型的研究与开发
2.
High availability(HA) realizing of dynamic soft reduction process control system for slab continuous casting machine;
板坯连铸机动态轻压下过程控制系统的高可用性实现
3.
Research on dynamic secondary cooling control model for slab continuous casting machine with high casting speed;
高拉速板坯连铸机动态二冷控制模型研究
5) slab casting
板坯连铸
1.
Discussion of computational methods for the forces incurred in the bending phase in slab casting;
板坯连铸弯曲阶段力能参数计算方法探讨
2.
Numerical simulation on fluid field in mold for slab casting;
板坯连铸结晶器内钢液流场的数值模拟
3.
Application of continuous straightening on slab casting;
连续矫直技术在板坯连铸中的应用
6) continuous casting slab
连铸板坯
1.
Cause analysis and control measures of longitudinal cracks on the surface of continuous casting slabs;
连铸板坯表面纵裂纹原因分析及控制措施
2.
Study on the characteristics of central macrosegregation in moderate thickness continuous casting slabs;
中等厚度连铸板坯中心宏观偏析特性研究
3.
Study on intermedium cracks of continuous casting slab and improvement practice;
连铸板坯中间裂纹成因分析及改进实践
补充资料：渤海铝业有限公司铝板坯连铸连轧机生产卷毛料
渤海铝业有限公司铝板坯连铸连轧机生产卷毛料
渤海铝业有限公司铝板坯连铸连轧机生产卷毛制
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条