1) organic carrier
有机载体
1.
Development of organic carrier for PDP phosphor paste;
PDP荧光粉浆料用有机载体的研制
2.
A comment was carried out on characters of metallocene catalyst with organic carrier, the approaches for supporting as well as the influences of supporting on capability of the catalyst in olefin polymerization and properties of the polymers.
综述了近年来天然高分子、聚合物等有机载体用于负载茂金属催化剂的研究现状,评述了有机载体型茂金属催化剂的特点、负载方式、负载化对催化烯烃聚合性能和聚合物性能的影响。
3.
The influence of the three components (function phase, organic carrier, glass phase) of high sintering temperature silver paste upon its quality was discussed in this paper.
讨论高温银浆的功能相、有机载体和玻璃相三大组成部分对高温银浆品质的影响 ,得到了一些对高温银浆的开发、研制有益的结论。
2) organic vehicle
有机载体
1.
The influence of organic vehicle with different proportion on the void rate of sintered film was compared.
观察了低温烧结型银基浆料烧结膜的表面形貌,比较了有机载体含量对浆料烧结膜孔洞率的影响,分析了单一溶剂及混合溶剂有机载体所配浆料的TGA曲线。
2.
In the temperature range 70~190℃, the volatility characteristics of the mainly used solvents and the mixed solutions, as well as the terpineol ethyl cellulose solution which as the organic vehicle were determined by the loss after being kept at a fixed temperature for twenty minutes.
用恒温失重方法研究了70~190℃范围内,电子浆料常用松油醇乙基纤维素体系有机载体和主要溶剂的挥发特性,得到了其在一定温度下保温20min的挥发量数据和适合制作电子浆料的有机载体配方。
3.
Pt electrode of plate oxygen sensors was prepared by means of screen printing,and the effects of different types of organic vehicle and binder on the sintering performance of Pt slurry were investigated.
采用丝网印刷的方式制备平板式氧传感器Pt电极,研究不同种类的有机载体和黏结剂对Pt浆料整体烧结性能的影响。
3) organic hydrogen carrier
有机氢载体
4) organic heat carrier
有机热载体
1.
Discussion on the organic heat carrier on-the-spot flash gas phase heating system;
有机热载体就地闪蒸气相加热系统探讨
2.
The article introduces the shortage of conventional heating system and advantages of organic heat carrier heating system and the economic benefit brought by revamped heating system.
介绍传统加热方法的不足,着重介绍有机热载体加热系统的优点和改造后取得的经济效益。
3.
The paper introduces the development,research and manufacturing of the YGL-1200MA type organic heat carrier boiler.
介绍YGL-1200MA型有机热载体锅炉的开发研制过程以及该锅炉的结构特点。
5) Organic heat-carrying agent
有机载热体
6) organophilic carrier
亲有机载体
补充资料：有机覆层:有机覆层
在基体材料表面覆以有机材料的材料保护层。在机械製造中﹐有机覆层的绝大部分是涂装层﹐或称油漆层。此外﹐也有用橡胶或塑料作为覆层的。需要抗酸﹑硷和抗腐蚀性气体和液体的钢铁件﹐常用厚约 3毫米的橡胶(如氯丁橡胶)或塑料(如氯化亚乙烯共聚物)黏在表面﹐可长期保护基体不受腐蚀。这种覆层主要用在大型抗蚀容器或排气系统中。埋在土壤中的金属构件﹐常以聚乙烯带包裹保护。在喷鉬或喷不锈钢的表面上涂覆聚四氟乙烯﹐在150℃温度下摩擦係数很低﹐磨损轻微﹐适於製造低载荷和要求高度清洁的滑动轴承﹐或用在食品﹑精细包装和纺织机械上。各国的Du﹑Dx轴承都是以塑料与金属复合製成的。通过静电喷涂将环氧树脂﹑氯化聚醚﹑聚四氟乙烯以及聚氯乙烯等塑料粉末涂覆在金属表面﹐可获多种抗化学腐蚀性极好的覆层﹐可用於输水﹑污水处理和海洋平台的设备上。有机覆层在辉光放电情况下﹐有机单体可以聚合成无针孔的有机膜﹐用作电容器的介质层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条