1) anodic aluminum oxide
AAO
1.
EVA Nanotubes fabricated by wetting of anodic aluminum oxide(AAO) template;
浸润AAO模板法制备EVA纳米管阵列
2.
Many of one dimensional nanostructures and their array of polyamide66(PA66),polypropylene(PP),acrylonitril-butadiene-styrene copolymer(ABS),thermoplastic polyurethane(TPU) are prepared by depositing a solution or melt of polymers into anodic aluminum oxide(AAO) template with a smaller pore of about 200 nm.
以孔径为200 nm的多孔氧化铝膜(AAO)为模板,采用聚合物溶液或熔体浸润模板纳米孔的物理技术,进行了多种一维聚合物纳米阵列的制备研究。
3) AAO template
AAO模板
1.
Study on electrochemical polishing technics for high purity aluminum during preparation of AAO template;
AAO模板制备中高纯铝电化学抛光工艺的研究
2.
Then, arrays of manganese dioxide nanowires were prepared using AAO template by sol-gel method.
利用扫描电镜(SEM)对模板和纳米线材料的形貌进行了表征,结果表明:采用该方法成功制得线状的氧化镍,长度可达亚微米级,直径约为100nm,与AAO模板的孔径大小基本一致,因此可以通过调节AAO模板的孔径大小来实现氧化镍纳米线的可控生长。
3.
The current-time curves of oxidation process during preparing AAO template in different experimental conditions were recorded by computer,and each stage of the process was analyzed.
我们使用计算机记录了不同实验条件下制备AAO模板过程中的电流曲线,并对其各阶段进行分析,提供了一种新的简单的估计AAO模板孔洞直径大小的方法,适应了纳米材料工业化生产的趋势。
4) anaerobic-anoxic-oxic system
AAO系统
5) AAO substrate
AAO衬底
6) AAO process
AAO工艺
1.
Fully coupled activated sludge model (FCASM3) Part 3:Numerical simulation of AAO process for optimum operating conditions;
全耦合活性污泥模型(FCASM3)Ⅲ:AAO工艺最佳运行工况数值模拟
2.
Pe (Peclet number) effects for wastewater treatment of Deqing Shishan WWTP′s AAO process were studied using the validated Biological-Hydraulic coupled model (FCASM3-Hydro) based on the Fully Coupled Activated Sludge Model 3 (FCASM3).
利用校验完成的生物场-水力场耦合模型(FCASM3-Hydro)以及生物场-水力场-温度场耦合模型(FCASM3-Hydro-Temp)对德清县狮山污水处理厂的AAO工艺系统进行模拟,分别考察反应池Pe准数值以及温度对污水处理效果的影响。
3.
Local experiments for Biological-Hydraulic-Temperature coupled model validation were carried out in the Deqing Shishan WWTP with an AAO process.
以采用AAO工艺的德清县狮山污水处理厂作为生物场-水力场-温度场耦合模型校验的现场试验基地。
补充资料：AAO
分子式：C2H5NO
分子量：59.07
CAS号：107-29-9
性质：密度0.969。熔点44-46°C。沸点115°C。折射率1.425-1.127。闪点38°C。水溶性soluble。
分子量：59.07
CAS号：107-29-9
性质：密度0.969。熔点44-46°C。沸点115°C。折射率1.425-1.127。闪点38°C。水溶性soluble。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条