1)  coalescing internal
聚结填料
1.
The separating behavior of gravitational oil/water separator models with or without a coalescing internal installed was studied through an oil/water separation simulating system.
利用重力式分离模拟试验装置,对添加聚结填料前、后分离器的分离特性进行了对比研究。
2)  Coalescence packing
波纹板聚结填料
3)  coalescence
聚结
1.
Analysis of coalescence mechanism and coalescence reaction dynamics;
聚结除油反应机理及其动力学分析
2.
Method of booster and coalescence for hydrocyclonic matching technology;
旋流配套工艺中的增压与聚结方式
4)  agglomeration
聚结
1.
The agglomeration phenomenon of 7-aminocephalosporanic acid (7-ACA) crystals made from two different crystallization processes is studied.
对7-氨基头孢烷酸(7-ACA)两种结晶方法的聚结现象进行研究。
2.
The breakage model including two - body equal - volume birth function and two - body powerlaw death function was used in the agglomeration and breakage population balance model .
通过采用MSMPR反应沉淀器,研究了普鲁卡因青霉素反应沉淀过程中粒子的聚结和破裂对过程的影响机理,并对用生死函数表征聚结和破裂的粒数衡算模型采用新的分析方法。
5)  aggregation
聚结
1.
The aggregation and agglomeration of particles are important secondary kinetic processes in crystallization and precipitation,which evidently affect the shape,the size distribution and the purity of the final products.
粒子聚结及团聚是结晶及沉淀过程中重要的二次动力学过程,对最终产品的晶形、粒度分布及纯度影响较大。
2.
The results show that freeze drying can improve effectivly aggregation behaviour of grains during gel drying.
结果表明,冷冻干燥法能够有效地改善凝胶干燥过程中粒子间的聚结性能。
3.
The effects of PVP in formulation and freeze thawing steps on drug leakage and aggregation of tanshinone liposomes were investigated.
考察了聚乙烯吡咯烷酮 (PVP)以及冻融处理对丹参酮脂质体的药物渗漏和微粒聚结特性的影响。
6)  coalescing internal
聚结构件
1.
The velocity vector and flow field inside the separator with two different inlet internals, four different flow regulating internals and six different coalescing internals are obtained, and the separation features of different internals are analyzed and compared.
应用Fluent软件的标准κ-ε模型和多相混合模型,对重力式分离器的油水分离内流场进行了三维数值模拟,得到含有2种不同入口构件、4种不同整流构件和6种不同聚结构件的分离器内部速度矢量和流场,分析并比较了不同构件的分离特性。
参考词条
补充资料：填料函填料
分子式：
CAS号：

性质：又称填料函填料或螺旋盘根。主要用于填塞反应釜、搅拌器、泵等旋转轴或往复活塞杆及阀杆轴贯通处的填料函(stuffing box)，以抑止旋转或往复运动的轴杆处的低压蒸汽、气体、热水、溶液及各种介质的泄漏。常以棉麻、石棉、聚四氟乙烯、碳纤维、金属箔等单独或几种材料组合，经捻合、编织或与橡胶并用制成，为条状产品。横断面有正方形、梯形、圆形等，填料条按其截面大小绕成不同直径的螺旋状制品，使用时将其切断成适当周长的环，卷于轴的四周，依次塞入填料函中，用盖锁紧，完成密封。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。