1) contact zone
接触区域
1.
Using the computer to analyse and revise the tooth contact zone by the tooth contact analysis(TCA),the basic principles and the current development and its trendency for the technology of Tooth Contact Analysis(TCA) has been introduced.
通过对齿轮齿面接触分析TCA技术(利用电子计算机进行齿面接触区域的分析和修正)的研究,介绍了齿面接触分析TCA技术的基本原理、发展现状以及发展动态,阐明了TCA技术在现代工业生产中重要意义。
2.
Based on the cutting theory of Klingelnberg spiral bevel gear system,the geometrical correction model of the contact zone to Klingelnberg spiral bevel gear system is established.
基于克林根贝格螺旋锥齿轮的切齿理论,建立了克林根贝格螺旋锥齿轮接触区域的几何修正模型,给出了影响齿长、齿高方向接触位置的因素和产生对角接触原因,推导了调整接触区位置各参数的调整量计算公式,提出了齿长和齿高方向和对角接触的接触区域调整方法。
2) Contact area
接触区域
1.
On this basis,driving error and contact point of gear pair can be calculated with relevant program,thus driving error curve and contact area of gear pair are achieved.
在此基础上,编制相应程序即可计算出误差条件下齿轮副的传动误差和接触点,从而可以获得齿轮副的传动误差曲线和接触区域。
3) contact zone outline
接触区域轮廓
1.
Based on the fact of the screwfeed of the blank during the rotary - forging, the paper offers a numerical calculate process for the contact zone outline of the ring parts and provides an exact method of calculation for the contact area.
本文从摆动辗压过程中坯料螺旋式送进的事实出发,给出了环形坯料接触区域轮廓坐标的数值求解过程,为正确计算接触面积提供了精确的计算方法。
4) bearing contact
接触域
1.
It is the 2nd problem of conjugate surface that solve the bearing contact of gear and the gear ratio relation under given position with two known surfaces.
已知两曲面,在既定的位置条件下,求传动的接触域及速比关系属于共轭曲面的第二类问题,也是该领域的难点问题之一,用传统的方法解决起来非常复杂。
2.
The article introduces the simulation principle of conjugate gear tooth surfaces, brings proposes a new numerical calculation method for bearing contact on conjugate gear tooth surfaces based on simulation principle, presnts the solving steps.
介绍了共轭齿面的仿真原理,提出基于此原理的共轭齿面接触域求解新方法,给出求解步骤。
5) multi body contact
多域接触
1.
The coupled boundary integral equations for the multi body contact problem with friction in 3D elasticity and the criterion for correct contact state are derived in this paper.
给出了求解任意的三维多域有摩擦弹性接触问题耦合边界积分方程的一般表达式和接触修正及收敛判定准则，编制出求解三维多域接触问题的二次等参边界元程序。
6) contact areas
接触领域
1.
Using the finite element method,with a special algorithm by treating the contact areas as zero-aperture elements,numerical simulations of fluid flow in joints were conducted.
考虑节理面上的接触领域的非透水性,用有限元法对节理中的渗流进行数值模拟。
补充资料：区域经济规划（区域规划）
区域经济规划（简称区域规划）是区域经济发展战略的具体安排，是战略思想的细化。区域规划应当是区域经济发展战略指导下的区域和产业发展的详细的安排。它包括区域发展、产业发展、土地利用、城镇体系等多方面的内容。它与发展战略的主要区别在于，战略应是粗线条的、具有指导意义的纲领；规划应是细线条的，具有实施功能的安排。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条