1) fill factor
填充系数
1.
Confirmation of new photodetector and its fill factor;
新型光电探测器及其填充系数的确定
2.
The integration technique is applied to 256×256 PtSi CCD, and has made its fill factor increased by 2.
微透镜与红外256×256PtSiCCD的集成结果表明,微透镜填充系数提高了2。
3.
The results show that the performances of graded gravel mixture are improved significantly after being treated with cement and lime,especially when fill factor is 0.
研究表明,掺加二灰后级配碎石混合料的性能显著提高,特别是二灰的填充系数为0。
2) filling coefficient
填充系数
1.
Researches on filling coefficients for stability of soil stratum permeability;
土体渗透稳定性的填充系数分析计算方法
2.
Based on the comparison between theoretical calculation and test results,this paper suggests that the filling coefficient of c.
通过理论计算与试验结果的对比,建议冠状铆钉干涉配合的填充系数可取为0。
3) Fill-factor
填充系数
1.
At present the cell array lens is usually cylinder or hemispheroid whose fill-factor(the ratio of light area and total area) can achieve about 90.
由于传统的圆形孔径透镜阵列填充系数较小,而在模拟复眼光学系统中需要高填充系数的透镜阵列。
2.
But at present the cell array lens is usually cylinder or hemispheroid, although the hexagons arrange is used, whose fill-factor (the ratio of light area a.
目前所使用阵列的透镜元多是圆柱形或半球形的,尽管采用六角形排列其填充系数(受光面积与总面积的比率)最高能达到90。
4) Filling factor
填充系数
1.
A full focusing filling factor is introduced.
首先,通过分析平行轴和共轴激光雷达接收、发射系统的结构,引入了可完全聚焦填充系数,从几何光学角度推导了两种填充系数的表达式,从而界定了几何因子值的理论范围。
5) filling coefficients
填充系数
1.
The numerical method of the space-time conservation element and solution element(CE/SE) is deduced to simulate the interior flow of pulse detonation engine(PDE) with different filling coefficients.
推导了守恒元与求解元(CE/SE)方法的计算格式,用于对几种不同填充系数的脉冲爆震发动机内流场进行计算,发现CE/SE方法是一种较好的爆震波模拟方法,能够有效地捕获爆震波等强间断。
2.
Under same excess coefficient α,and various filling coefficients β,the detonation pressures are measured,and the factors influencing detonation pressures are analyzed.
测试了在同一余气系数α、不同填充系数β下的爆震波压力,并对其变化进行了分析。
6) packing factor
填充系数
1.
In this paper, the packing factor of the coatings prepared by glancing angle deposition is analyzed under the conditions that the flux arrival angle of coating material is α and the columnar microstructure inclination angle of coatings is β.
本文首先探讨了膜料的沉积入射角为α,薄膜柱状生长倾斜角为β时的薄膜的填充系数;之后利用drude理论,分析研究了斜角入射沉积法制备渐变折射率薄膜的折射率与薄膜的入射角和生长方向的关系。
补充资料:填充系数
也称叠片系数 (lamination factor)。指一定量的电工钢板叠片的理论体积(计算值)与实际体积(通常在一定压力下测定)之比,也就是净金属占铁芯体积的百分比。填充系数是衡量铁芯实际紧密程度的一个量度。填充系数高意味着铁芯体积不变时,由于电工钢板用量增多而有更多的磁通密度通过,有效利用空间增大。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条