1) compression bar
压杆
1.
Calculated length of compression bar in pile bent column pier;
单排桩柱墩压杆的计算长度
2.
Stability and reliability optimization of arbitrarily-distributed parameters for compression bars;
任意分布参数的压杆稳定可靠性优化设计
3.
A new approximate formula for the large deflection problem of compression bar with two ends are simply supported is obtained,by the use of Ritz-Galerkin method.
通过非线性振动中常用的里兹-伽辽金法,推出了两端铰支压杆大挠度问题的一个新近似公式,计算结果表明具有较高的精度。
2) column
[英]['kɔləm] [美]['kɑləm]
压杆
1.
Critical press analysis on cracked slender columns;
含裂纹细长压杆临界力分析
2.
Process condition of upsetting shoulder was discussed and forming force was calculated based on column buckling theory.
基于压杆稳定理论,探讨了该制件镦压凸肩的工艺条件,计算所需的工艺力,介绍其镦压成形模具的设计结构、工作原理。
3.
In this paper the stability of a compressed column with initial imperfection and arbitrary supported ends is studied systematically.
对各种边界条件下初始缺陷压杆的稳定性进行了系统的研究,讨论了不同边界条件和初始挠度对压杆稳定性的影响,得出了求解弹性边界约束系数、端点转角、端点弯矩和压杆挠度的公式,为进一步的理论分析打下了基础。
3) Compressive bar
压杆
1.
Reliability-robust design of compressive bar under incomplete probability information;
不完全概率信息的压杆稳定可靠性鲁棒设计
2.
Reliability-based robust design of compressive bar;
压杆稳定可靠性稳健设计
3.
Stable reliability-based sensitivity design of compressive bar;
压杆稳定可靠性灵敏度设计
4) strut
[英][strʌt] [美][strʌt]
压杆
1.
Experimental study on flexural torsional buckling of cut-T struts;
剖分T型钢压杆的弯扭屈曲试验研究
2.
The method is proved to be both accurate and simple by comparing the theoretical values with the experimentally measured values of the elastic stability tests of struts and frames.
分析了结构失稳时Ｐ－δ试验曲线的图形性质；提出了以最大曲率推算结构失稳临界荷载；并导出了相应的计算公式，压杆和刚架弹性稳定试验的实测数据说明本文所述方法既精确又简便，特别是结构或模型不允许作破坏试验时，可直接推算失稳临界荷载。
3.
The width-thickness limit of T-section strut prescribed in the code for design of steel structure (GB50017—2003) is broadened so as to promote the using of the hot-rolled cut T-section strut.
《钢结构设计规范》(GB5 0 0 1 7— 2 0 0 3 )放宽了热轧剖分T型钢压杆腹板高厚比限值 ,促进了剖分T型钢的推广使用。
5) compressive rod
压杆
1.
Using the fundamental knowledge of mathmatical analysis,this paper estabilishes the general controlling equation of a compressive rod under a combined load.
利用数学分析的基本知识建立了联合载荷作用下压杆的一般控制方程。
2.
By analysizing the natural properties of a compressive beam and removing the ordinary solution,this paper gives a detail method for calculating the critical forces of compressive rods with several kinds of different boundary conditions using vibration theory.
以轴向受压梁的固有振动分析为基础,利用线性代数的基本知识,通过去除平凡解的方法,导出了计算压杆临界力的公式。
6) compression member
压杆
1.
This article presents a unified analysis of the limiting slenderness of plate elements of compression members with three commonly used sections.
本文统一分析了轴心压杆三种常用截面的板件宽厚比限值。
2.
There is no specification for the design of welded H section or box section compression member which plate thinkness is over 40 mm.
对于板厚达４０ｍｍ以上的厚板焊接Ｈ形或箱形压杆承载力的设计，我国目前尚无规范可循。
补充资料：复盛螺杆式空压机用油气分离滤芯
压缩机进气除尘滤芯、油过滤芯、油气分离滤芯、进口压缩气体高效过滤器芯国产化、粉尘滤芯、高精度玻璃纤维烧结式滤管、含油尾净化设备，透平机尾气除油滤芯厨房油烟净化，房下水用油水分离器。化工填料：木业、抛光、粉碎、粉制剂行业的粉尘回收器、电火花，线切割等机床过滤滤芯、化工食品精油过滤器、神宝不锈钢微孔过滤器。各种气体、液体、粉尘等测试仪器，神宝在线监测设备滤芯，喷粉设备滤芯。各种压缩机油汽分离器滤芯。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条