1) axial compression
轴压
1.
Buckling analysis of three dimensional braided composite cylindrical shells under axial compression;
三维编织复合材料圆柱壳轴压下的屈曲分析
2.
Interactive buckling and plates' slenderness of T section under axial compression;
轴压T形钢的相关屈曲及板件宽厚比
3.
Analysis of relation between the axial compression and the axial displacement for the inner core in a sleeved column;
套管构件中轴压内核本构关系的分析
2) Axial load
轴压
1.
Finite element methods on ultimate load-carrying capacity of CFST dumbbell shaped short columns under axial loads;
钢管混凝土哑铃型轴压构件极限承载力有限元分析
2.
Experiments of 10 concrete-filled-steel tubular (CFST) dumbbell-shaped Long columns with various slenderness ratio subjected to axial load were carried out, in which 5 specimen were failed in the strong-stress-axis direction; another 5 were failed in the weak-stress-axis direction.
共进行了10根不同长细比的钢管混凝土哑铃形轴压长柱(5根强轴向破坏,5根弱轴向破坏)的试验研究。
3.
Based on the experimental results,theoretical analysis was conducted to study the influence of axial loads on the flexural capacity of this type of connections.
在此基础上,研究了轴压作用对方钢管混凝土柱内隔板式节点抗弯承载力的影响,提出了3块内隔板情况下节点抗弯承载力的计算方法。
3) axial loading
轴压
1.
In this paper axial loading is adopted in order to reduce the tensile residual stress.
结果表明：轴压在一定范围内，降低残余应力的效果较明显。
2.
1 contrast unstrengthened square reinforced concrete column and 10 reinforced concrete columns strengthened by circular steel jacket were tested under axial loading.
为研究圆形钢套管加固混凝土柱的基本力学性能,进行了1根未加固的普通钢筋混凝土柱和10根圆形钢套管加固的混凝土短柱在不同加固钢套管厚度及初始轴压比下轴心受压试验,初始轴力通过对未加固试件施加后张预应力来进行模拟;在试验研究的基础上,根据应变协调原则对加固后构件轴压承载力进行了数值分析。
3.
Utilizing the stress-strain relations of steel and concrete presented in the literature for concrete filled rectangular steel tubes, a numerical method is applied for the analysis of load-deformation curves of the double-skin composite members subjected to axial loading.
在确定组成矩形钢管混凝土的钢材和核心混凝土应力应变关系模型的基础上,利用数值解法对矩形中空夹层钢管混凝土轴压构件的荷载-变形关系进行了全过程分析。
4) shaft pressurization
压轴
1.
Specific improvements have been implemented on both shaft pressurization process and shaft alignment process.
通过对电机生产线现状的分析,提出了电机生产线可重组技术思路和系统总体框架,并对压轴工位和转轴校直工位进行了重点改造,通过增加生产线上加工设备的反馈能力,使加工设备的加工能力和使用情况得到实时监控,实现了整个电机生产系统对产品变化的快速响应,产品质量得到明显提高,品种适应能力达到理想质量控制水平。
5) triaxial compression-compression-tension
三轴拉压压
1.
Experimental study of mass concrete under biaxial compression-tension and triaxial compression-compression-tension stresses;
大坝原级配混凝土在双轴拉压及三轴拉压压受力状态下的试验研究
6) central and eccentric load
轴压与偏压
补充资料：压轴
1.见"压胄子"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条