1) boronizing process
渗硼工艺
1.
The boronizing process parameters of Cr12MoV steel and the RE addition were optimized by orthogonal experiment.
采用正交试验方法,优化出Cr12MoV钢最佳的渗硼工艺参数为950℃×5 h及最佳的稀土加入量为0。
2.
The method of orthogonal experiment was used to investigate the effect of parameter of boronizing process on the thickness of the boride layer.
运用正交实验法来确定渗硼工艺的参数(渗硼温度、渗硼时间、稀土加入量和铬加入量)对渗硼层厚度的影响，从而确定合理的渗硼工艺。
2) cast-boronization process
铸渗硼工艺
1.
A boronized layer with relatively high hardness and wear－ resistance was formed on the casting surface by using cast－ boronization process.
利用铸渗硼工艺在铸件的表面形成一层硬度较高耐磨性较好的硼化物层，通过对铸渗硼层的显微组织进行分析，发现在铸渗硼剂中加入铜粉可使硼化物层致密，并使铸渗硼层内缩孔、气孔等缺陷较少。
3) infiltration process
浸渗工艺
1.
The influence of wetting angle, capillary force, infiltration pressure, infiltration temperature, infiltration time and interface on the infiltration process for RC-MMCs was also introduced.
综述了润湿角、毛细力、浸渗压力、浸渗时间和浸渗温度以及界面对网络陶瓷增强金属基复合材料浸渗工艺的影响,提出下一步需要改善浸渗行为的措施。
4) cast-penetration technics
铸渗工艺
1.
By varying cast-penetration technics ,the influence of thickness and quality in composite layer with Si by casting on the surface of cast steel were studied.
研究了不同铸渗工艺对铸钢件表面铸渗硅复合层厚度和质量的影响。
5) carburizing process
渗碳工艺
1.
This paper deals with the carburizing process,microstructure,mechanical properties and quenching distortion of the air cooling low carbon bainitic steel.
对低碳贝氏体钢的渗碳工艺、显微组织、力学性能、淬火变形进行了研究。
补充资料：渗硼
分子式：
CAS号：
性质：渗镀品种之一，欲渗入的元素为硼。渗硼方法有固体粉末渗硼、气体渗硼、电解盐浴和盐浴的液体渗硼。渗硼层有优异的耐磨性、较好的耐蚀性和抗高温氧化性。例如钻井设备的泥浆泵零件，冲压、拉丝等模具经渗硼后可提高使用寿命。
CAS号：
性质：渗镀品种之一，欲渗入的元素为硼。渗硼方法有固体粉末渗硼、气体渗硼、电解盐浴和盐浴的液体渗硼。渗硼层有优异的耐磨性、较好的耐蚀性和抗高温氧化性。例如钻井设备的泥浆泵零件，冲压、拉丝等模具经渗硼后可提高使用寿命。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条