2) kinetic metallization
动力金属喷涂
1.
A Ni53Nb20Ti10Zr8Co6Cu3 fully amorphous metallic coating with thickness of about 500μm was prepared by kinetic metallization (KM) spraying gas-atomized powders.
用气体雾化法制备了Ni53Nb20Ti10Zr8Co6Cu3非晶合金粉末,将粒度小于25μm的非晶粉末用动力金属喷涂工艺制备了非晶涂层。
3) cold spraying
冷喷涂
1.
Study of incidence angle of particle on its coating formation in cold spraying;
粒子入射角度对冷喷涂涂层形成的影响
2.
Influence of heat treatment on interfacial diffusion of Al alloy cold spraying coating on magnesium alloy;
镁合金表面冷喷涂铝合金的界面扩散行为
3.
Applications and prospect of cold spraying technique in welding engineering;
冷喷涂在焊接工程中的应用与展望
4) cold spray
冷喷涂
1.
Research on computational simulation of two-phase jet flow in cold spray technology for manufacture of functional coatings;
冷喷涂制备功能涂层工艺中两相射流数值模拟研究
2.
Rapidly Solidified Zn-Al Powder on Surface of Mg Alloy by Cold Spray Method;
镁合金表面冷喷涂快凝Zn-Al合金粉末的研究
3.
Wear behavior of cold spray Zn-Al alloy coating on magnesium alloy;
镁合金表面锌铝合金冷喷涂层的磨损行为
5) cold gas dynamic spray
冷喷涂
1.
Advantages and disadvantages of five kinds of thermal spraying technologies including high velocity oxygen fuel flame spraying process, hypersonic plasma spray process, laser spray process, reactive spray process and cold gas dynamic spray process were analyzed.
对超音速火焰喷涂、超音速等离子喷涂、激光喷涂、反应热喷涂和冷喷涂等5种不同的热喷涂工艺的优缺点进行了分析。
2.
Numerical simulations are performed for the gas particle two phase flow in the cold gas dynamic spray process to investigate the acceleration of micro and nano particles with diameters ranging from 100 nm to 50 μm.
冷喷涂过程中,由于基板的存在,板前有激波出现,从而对喷涂粒子的运动产生影响。
3.
The particle velocity in cold gas dynamic spray (CGDS) is one of the most important factor that can determine the property of the bonding to the substrate.
冷喷涂(CGDS)过程中粒子速度是决定粒子粘附性的最重要的因素之一。
6) cold gas dynamic spraying
冷喷涂
1.
Properties of Cu coating in supersonic cold gas dynamic spraying;
超音速冷喷涂铜涂层特性分析
2.
Cold gas dynamic spraying(CGDS) was a newly-developed coating techniques proposed in 1980 's, in which the carrier gas was accelerated to very high speed (usually supersonic) by de Laval nozzle, then the particles carried by gas impinged on the substrate and form coating.
冷气体动力喷涂(简称冷喷涂)是上个世纪80年代提出的一种全新的喷涂工艺，它是利用拉法尔喷管将输送气体加速到超音速，使之携带喷涂粒子撞击基板形成涂层。
3.
Copper coating on aluminum substrate was prepared by cold gas dynamic spraying for hydrogen production through methanol steam reforming.
9%,表明能用冷喷涂技术制备甲醇水蒸气重整制氢的催化涂层。
补充资料：冷气
冷气
冷气 病证名。脏腑之气与寒冷相搏所致的疾患。《诸病源候论·冷气候》：“夫藏气虚，则内生寒也。气常行府藏，府藏受寒冷，即气为寒冷所并，故为冷气。其状或腹胀，或腹痛，甚则气逆上而面青手足冷。”《圣济总录·诸气门》：“冷气者，因寒冷搏于气所为也。”证见呼吸少气，胁肋刺痛，皮肤拘急，恶寒战栗，百节酸疼，咳嗽声嘶，膈脘否塞。方用沉香丸等。参见气病条。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条