1) Casting slip
浇注泥浆
2) pouring
浇注
1.
The two 1080-m3 blast furnaces in the Ironworks successively went into operation at the end of 2005,the frontside main runner being of semi-pouring,semi-ramming mix.
莱钢炼铁厂银山前区2×1080m3高炉于2005年底相继投产,炉前主沟为半浇注、半捣打料混合主沟。
2.
HSLH serial pouring cooling feeding system can regulate mould cooling period and flexiblly choose shakeout range.
HSLH系列砂模浇注冷却输送系统,可调节铸型冷却周期,灵活选择浇注落砂区,液压传动平稳可靠,触摸屏操作PLC控制,机械手自动套箱压铁,故障自诊断。
3.
Meanwhile,this paper described many technical innovation applied to quantitative pouring unit,disk mould (assembling) machine,kick-off plate flat unit and chain plate unit design.
结合工程设计,介绍了铅阳极铸型机组的结构组成及主要技术参数,并对定量浇注装置、圆盘铸型机、取板平板装置、排板装置等技术创新作了一定的阐述。
3) casting
浇注
1.
Thermal and mechanical properties of casting polyurethane resin with heat resistance;
浇注型耐热聚氨酯树脂材料的热性能和力学性能
2.
The Study of Epoxy Resin Casting Technique for Dry-Type Transformer;
干式变压器环氧树脂浇注工艺探索
3.
To achieve the low superheat casting,a kind of cooling nozzle is developed.
为实现低过热度浇注,开发了一种冷却水口。
4) cast
浇注
1.
Application of New Binding Structure of Core Limb to Cast Dry-Type Transformer;
新型铁心柱绑扎结构在浇注型干式变压器中的应用
2.
Analysis of Environmental Protection Characteristics of Epoxy Resin Casting Dry-Type Transformer;
环氧树脂浇注干式变压器环保特性分析
3.
Cast Process of Winding in Epoxy Resin Cast Dry-Type Transformer;
环氧树脂浇注干式变压器的绕组浇注工艺
5) pour
浇注
1.
It is further proposed to pour glass glue for the sealing during the process .
针对传统的牵引电动机定子主极、换向极装配中的工艺材料缺陷,提出了采用环氧树脂和聚酰胺树脂添加H级填充泥这种新的磁极装配材料的方法,该磁极装配材料一体化程度高、密封性强,可以有效地防潮、防接地;并提出工艺实施过程浇注玻璃胶密封。
6) protective casting
保护浇注
1.
The measures of controlling aim carbon content and pre-deoxidation,consolidating refining deoxida- tion and light blow after steel tapping,protective casting,etc.
通过采用控制出钢终点碳和预脱氧,加强精炼脱氧和出钢软吹,做好保护浇注等措施,降低了钢中氧含量。
2.
The Special Steel Plant successfully developed 37Mn steel for Class J55 oil well pipes on its first test,by adopting the measures such as the use of EAR-LF-CC process flow to set down reasonable technical measures,strictly controlling aim carbon content,preliminary elimination of oxygen,adjustment of refining slag and protective casting.
特殊钢厂采用EAF-LF-CC工艺路线研制,通过制定合理技术措施,严格控制钢终点碳、预脱氧,调整精炼炉渣、连铸保护浇注等措施,一次成功开发了J55级油井管用37Mn5钢。
3.
The high quality 37Mn5 tubular billet for oil well pipe has been developed and produced in Laigang by the following short flow process: UHP EAF smelting-LF refining-continuous casting – hot charging – rolling,in which some process measures such as prepared burden,strengthening deoxidation,protective casting and so on have been adopted.
莱钢采用UHP电炉冶炼-LF精炼-连铸-热送-轧制短流程工艺路线开发生产J55级37Mn5油井管坯钢,采取了精料、精炼强化脱氧、连铸保护浇注等工艺措施,使生产出的产品成分均匀、残余元素含量低、氧含量低、夹杂物少、晶粒细小,满足了石油工业对高质量油井管的要求。
参考词条
补充资料：咸水泥浆、海水钻井液、海水泥浆
分子式：
CAS号：
性质：又称咸水泥浆、海水钻井液、海水泥浆。氯离子含量在6000mg/L以下的水基钻井液。
CAS号：
性质：又称咸水泥浆、海水钻井液、海水泥浆。氯离子含量在6000mg/L以下的水基钻井液。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。