1) support
[英][sə'pɔ:t] [美][sə'pɔrt]
支座
1.
Finite Element Calculation and Strength Evaluation of the Local Stress in the Support Locations of Vessels;
容器支座区域局部应力的有限元计算和强度评定
2.
Failure analysis of the ethylbenzene superheater 's supports;
苯乙烯装置过热器组支座受力分析
3.
Structure Improvement of Retarder's Supports for Glassed Steel Chemical Reactor;
搪玻璃反应罐减速机支座结构的改进
2) bearing
[英]['bɛəriŋ，'beərɪŋ] [美]['bɛrɪŋ]
支座
1.
Nonlinear finite element analysis of rubber-rigid spheres bearing;
橡胶-钢球支座非线性有限元分析
2.
One construction method for bearing replacement of T-beam bridge;
更换T梁桥支座的一种施工方法
3.
On one new arrangement form of bridge bearings;
关于一种新的桥梁支座布置形式的探讨
3) pedestal
[英]['pedɪstl] [美]['pɛdɪstḷ]
支座
1.
Fatigue and Durability Analysis of Pedestal of PC Beam for Light Rail;
跨座式轻轨PC轨道梁活动钢支座疲劳及寿命有限元分析
2.
Research on pedestal looseness fault of multi-disc over-hung rotor system
多盘悬臂转子系统支座松动故障研究
3.
A mathematical model with nonlinear oil film force was employed to study the pedestal looseness fault at two supports in a rotor-bearing system.
针对转子-轴承系统中两端支座发生的松动故障,建立了带有非线性油膜力的数学模型。
4) bracket
[英]['brækɪt] [美]['brækɪt]
支座
1.
The force loaded by spatial truss string structure roof to its under support and the mechanical response of roof itself with different roof brackets and different string initial tensile force are analysed.
根据国内张弦结构项目屋盖的关键受力构件布置方式与支承边界平面水平投影线的组合进行了屋盖结构分类,从屋盖支座设置方式和索初始预拉力入手,分析了张弦桁架结构屋盖在不同支座形式时不同索初始预拉力对下部支承结构的作用力及屋盖结构的力学响应。
2.
Combining FEM static analysis with dynamic optimization,this paper has an optimization design for the bracket of a coach steering gearbox with changing little strength and stiffness,and reaches the target of reducing the bracket weight.
利用有限元结构静力分析与动态优化设计相结合,对某客车转向器支座进行结构优化设计,在强度和刚度性能几乎不变的前提下,达到减轻支座重量的目的。
3.
And the bracket of an equipment was analyzed by ANSYS,learn that the ribbing has little influence on the stress distributing on the bracket and found the best project to design the bracket.
介绍了ANSYS的基本思路及其应用范围,并利用ANSYS软件对某设备上翻盖油缸支座设计方案进行了计算分析,得知支座上所设计的加强肋对支座本身受力作用影响不大,并进行了优化设计,从而找到更合适的设计方案。
5) bearer
[英]['beərə] [美]['bɛrɚ]
支座
1.
Introduction to Laminated Rubber Bearer Basic Shock Isolation Architecture;
叠层橡胶支座基础隔震体系介绍
2.
Because of uneven subsidence of the foundation,there occurred frame distortion and roofing fracture,for which,a series of strengthening construction has been carried in the treatment of frame bearer and member distortion,the set up of scaffolds and roofing maintenance.
由于地基不均匀沉降,出现网架变形及屋面板撕裂,针对这种情况,按照网架伸缩缝分段,逐段整改加固:从脚手架搭设到对网架的支座处理、杆件变形处理、屋面板维修的一系列加固施工方法。
3.
The bearer is the tie point between upper part and underpart in bridge structure.
在桥梁结构中 ,支座是上、下部结构的连接点 ,其作用重大 ,但由于年久失养或橡胶支座本身老化、钢板支座锈蚀失效等问题 ,有些已直接影响到桥梁上部结构安全 ,需要在不破坏桥梁本身结构的情况下对支座进行整体更换 ,使之恢复原有功能 ,以保证桥梁整体运行安全。
6) supports
[英][sə'pɔ:t] [美][sə'port]
支座
1.
Effect on the deformation of the body of coke drums due to the ascending of supports;
支座位置上移对焦炭塔塔体变形的影响
2.
There was a branch of indpendent remains,characterized as compound cookers with surrounding-bottom kettles and supports,in the North China Plain before 6500 AD.
距今6500年之前,华北平原存在着一支独立的圜底釜系遗存,它的突出特征是以圜底釜和支座作为复式炊具。
补充资料：支座
分子式：
CAS号：
性质：用以支承容器或设备的重量，并使其固定于一定位置的支承部件。还要承受操作时的振动与地震载荷。如室外的塔器还要承受风载荷。其结构型式主要由容器自身的型式和支座的形状来决定，通常分为立式支座、卧式支座和球形容器支座三类。立式支座又分为悬挂式支座、支承式支座、支承式支脚，支承式支腿、裙式支座等；卧式支座分鞍式支座、圈座和支腿式支座等；球形容器支座分支柱式、裙式、半埋式和V形支承等。
CAS号：
性质：用以支承容器或设备的重量，并使其固定于一定位置的支承部件。还要承受操作时的振动与地震载荷。如室外的塔器还要承受风载荷。其结构型式主要由容器自身的型式和支座的形状来决定，通常分为立式支座、卧式支座和球形容器支座三类。立式支座又分为悬挂式支座、支承式支座、支承式支脚，支承式支腿、裙式支座等；卧式支座分鞍式支座、圈座和支腿式支座等；球形容器支座分支柱式、裙式、半埋式和V形支承等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条