1) cast iron component
铸铁构件
1.
It is a complex process to estimate residual stress of cast iron components.
铸铁构件残余应力的评价过程一直相当繁琐。
2) Compression member of cast iron
铸铁承压构件
3) Iron casting
铸铁件
1.
Design of Kiss Gating-feeder System of Hydraulic Test Platform Iron Casting by Applying Moduli Calculation Method of Proportional Solidification;
运用均衡凝固模数法设计液压试验平台铸铁件压边浇冒口系统
2.
Through the contrast test between STMMA model material and EPS model material,it is found that: there is a difference for C content and hot cracking mechanism between these two model materials,so using the STMMA model material to substitute the EPS model material can decrease or eliminate the surface quality defects of iron casting.
通过STMMA模样材料与EPS模样材料的对比试验发现:两种模样材料的C含量和热裂解机制不同,使用STMMA模样材料替代EPS模样材料可以减轻或消除铸铁件表面质量缺陷。
4) cast iron part
铸铁零件
1.
In allusion to the problems of crack,air hole and etc which happened in the production process of soldering cast iron part,this paper studies and probes into the way of repairing cast iron part-heat-soldering,cold-soldering and calefaction & respond reducing soldering.
针对铸铁零件在制造及使用过程中常出现的裂纹、气孔等问题,研究探讨了修复铸铁零件的方法——热焊法、冷焊法、加热减应焊法。
5) iron castings
铸铁件
1.
The common defects of iron castings include:blow hole,sand inclusion,shrinkage,slag inclusion,metal penetration and burn-on,cracking,distortion,uneven hardness distribution,under-nodularizing of nodular irons,degradated spheroidisation,graphite floatation,and reverse chilling.
铸铁件常见的铸造缺陷有:气孔、砂眼、渣孔、缩孔、缩松、粘砂、裂纹、变形、硬度不均匀、球铁件球化不良、球化衰退、石墨漂浮和反白口等。
2.
The status of iron castings in automobile industry was briefly described.
简单叙述了铸铁件在汽车工业中的地位,详细评述了铸铁的资源优势、低能耗优势、价格优势和工艺优势,指出只有挖掘铸铁在特定性能上的潜力,才能与其它材质竞争取胜,保有在汽车上的份额并力争扩大的方向。
6) Gray iron casting
灰铸铁件
1.
This paper introduces the special properties of repair welding small defects for gray iron castings.
介绍了灰铸铁件小缺陷的特殊性 ,从焊补工艺上和材料的选用两方面考虑 ,有效地降低了焊接裂纹的产生 ,使母材与焊补金属熔合良好。
补充资料：Al-Li合金构件——歼7-II飞机舱口盖及副翼扰流片
Al-Li合金构件——歼7-II飞机舱口盖及副翼扰流片
Al—Ll合金构件——歼7一I 1机舱口盖及副翼扰流片 张自供稿
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条