1)  friction stir welding
摩擦搅拌焊（FSW）
2)  friction
摩擦
1.
Development of Research on Friction and Wear of High Performance and high Temperature Polymer Composites;
高性能耐高温聚合物复合材料的摩擦磨损性能研究
2.
Effect of friction on deforming condition during tube expanding process;
管材扩径时摩擦对变形状态的影响
3.
Determination of friction coefficient based on finite element analysis;
基于有限元分析的摩擦系数测定
3)  tribology
摩擦
1.
Tribology and Wear of MoS_2/Ti Composite Films;
MoS_2/Ti复合膜的摩擦磨损研究
2.
Tribology is the key factor that causes micro-components disabled in micro-electro mechanical system.
微机电中的摩擦是造成微构件失效损坏的关键因素,指出微机电中的摩擦属于原子分子尺度上的力学行为,具有不同于宏观摩擦的新特性。
4)  rubbing
摩擦
1.
In this paper, using infrared dichroism, the researchers quantitatively analyzed the LC scalar order parameters on the surface of an alignment layer after rubbing treatment.
液晶分子的取向排列通常需取向膜诱导引发,但实验发现强摩擦处理的取向膜表面的液晶分子有序度远低于液晶体内部的有序度,大约为体内部的1/2。
2.
With reference to the special features of Alstom type 330MW sets, the paper analyses the factors that causes high bearing temperature, the development of excessive vibration as well as ways of dealing with the rubbing between stationary and rotating parts.
该文结合ALSTOM类型机组特点,重点对蒙达公司1号机的轴承温度高和振动的发展过程,以及以后发生的动静部位摩擦的处理进行了分析,为同类型机组类似问题的分析和处理提供了一定的经验。
3.
discuss and based on the principle of electrostatic in PI rubbing process, study the effects of static accumulation in the rubbing cloth pile , PI dilution solvent, topcoat, humidity, X -ray and ionized gun ,discuss the experimental results and give suggestions on electrostatic improvement.
讨论了基于STN液晶显示器定向层摩擦静电原理,从摩擦布表面静电累积、PI稀释剂、TOPCOAT、湿度、离子风机和软X光等方面对静电影响进行实验研究,并对结果进行了讨论,提出了控制摩擦工序静电的建议。
5)  wear
摩擦
1.
Ball-on-disc T11 wear equipment and high temperature THT07-135 wear equipment were used to assess the slide wear factors of high velocity arc sprayed (HVAS) Fe-Al/Cr_3C_2 coating; SEM,TEM and X-ray methods were used to analysis the morphology and elements of wear scars, and the structure and phases of crossed sections.
使用球-盘接触式T11磨损试验机以及THT07-135高温磨损实验机对高速电弧喷涂Fe-Al/Cr3C2复合涂层进行了滑动摩擦影响因素的研究,并用SEM、TEM、X-Ray等手段观察分析了磨痕的形貌和成分、涂层截面的组织和相结构。
2.
Scanning Electron Microscope (SEM) analysis showed that water restrained the ability of polymers to form transfer film on steel counterface, the friction and wear were gove.
研究了PA66/PPS共混物在水润滑条件下的摩擦磨损性能。
3.
The research on tribology of steel(ferrous)-matrix composites reinforced by particles was reviewed in this paper, including tribological characteristics and properties of composite, the discussion of wear mechanism and the factors effecting wear resistance.
对颗粒增强钢基复合材料的摩擦学研究进行了评述 ,包括复合材料的摩擦学特征与性能研究 ,探讨了摩擦磨损机理以及影响耐磨性的各种因素 ,并在此基础上展望了其作为耐磨材料的未来发展前景。
6)  Rub
摩擦
1.
The results show that strong rub and grievous abrasion are the main reasons for the fracture of steelwire-line and the preventional methods are proposed.
采用化学分析、金相检验、硬度测试等方法,对钢丝绳断裂原因进行分析,结果表明,强烈摩擦和严重磨损是造成钢丝绳断裂的主要原因,并提出了预防措施。
2.
It is concluded that the rub between rotor and steam seal is the main reason for the abnormal vibration.
在对振动数据进行全面分析的基础上,指出汽轮机转子与汽封之间发生的动静摩擦是导致异常振动的根本原因。
3.
Both force and heat impacts act on the rotor simultaneously when rub fault occurs.
动静摩擦是旋转机械经常发生的故障。
参考词条
补充资料：焊接:摩擦焊
    利用工件端面相互摩擦產生的热量使之达到塑性状态﹐然后顶锻完成焊接的方法。车削工件时切屑往往牢牢地黏在刀头上﹐轴与轴瓦之间润滑不良时也会產生局部焊合﹐摩擦焊就是从这些现象出发而发明的。摩擦焊可分为连续驱动摩擦焊和惯性摩擦焊两种。①连续驱动摩擦焊﹕由电动机带动一个工件旋转﹐同时把另一工件压向旋转工件﹐使其接触面相互摩擦產生热量和一定塑性变形﹐然后停止旋转﹐同时施加顶锻压力完成焊接(图1 连续驱动摩擦焊 )。焊接质量与转速﹑摩擦时间﹑摩擦压力﹑顶锻压力和工件顶锻变形量有关。②惯性摩擦焊﹕由电动机驱动飞轮达到要求的转速﹐然后把一个工件压向夹持在飞轮轴上的转动工件﹐工件间的摩擦阻力使飞轮减速﹐并将飞轮的动能转换成焊接所需的热能(图2 惯性摩擦焊 )。焊接质量与飞轮惯性矩﹑转速和顶锻力有关。摩擦焊所用的摩擦焊机包括驱动系统(惯性摩擦焊机还包括飞轮)和加压装置。全自动焊机还有上﹑下料装置﹑去飞边装置和参数自动监控系统。摩擦焊适合於焊接杆件和管件﹐工艺简单﹑质量好﹐劳动条件好﹐生產率高﹐耗电量少﹐易於机械化和自动化。摩擦焊在工厂生產线上广泛用於发动机燃烧室﹑排气阀﹑轴﹑轴套﹑杆件﹑管子与法兰﹑石油钻杆和钻芯的连接和变截面杆件的连接。接头焊后不会產生金属间化合物。摩擦焊也常用於异种金属焊接﹐如铝与铜﹑钢﹑镍﹑镁合金﹔铜与钢﹑银等。摩擦焊在铝-铜导线过渡接头的焊接方面应用尤广。惯性摩擦焊也可焊接直径为 100毫米的棒材或截面积为60厘米2的管件。 
说明：补充资料仅用于学习参考，请勿用于其它任何用途。