1) honing
[英][həun] [美][hon]
珩磨
1.
Analysis of the honing of 465Q connecting rod;
465Q系列连杆珩磨工艺分析
2.
New Technology of Engine Cylinder Surface Quality Improving——Ultrasonic Vibration Honing;
提高发动机缸套表面质量的新工艺——超声振动珩磨
3.
Studies on pressing plate honing process for cylinder block of DongFeng-Cummins B series;
东风康明斯B系列缸体压板珩磨工艺研究
2) hone
[英][həʊn] [美][hon]
珩磨
1.
Mainly introduced one abrasive hone craft for deep hole processing,the high accuracy cold-drawn steel pipe may obtain the surface roughness Ra value very small,size precision and even shape precision all very high effect after directly precise processing on the abrasive engine bed.
主要介绍了一种深孔加工的强力珩磨工艺方法,高精度冷拔钢管直接通过强力珩磨机床进行精密加工,就可获得表面粗糙度Ra值很小,尺寸精度甚至形状精度都很高的效果。
3) laser honing
激光珩磨
1.
The new processing method of the cylinder wall:laser honing;
汽缸表面处理的新发展——激光珩磨
2.
Study on the technology of laser honing applied in machining the cylinder bore of engine;
发动机气缸孔表面的激光珩磨技术研究
3.
Experimental results indicate that it is practicable to apply single pulse interval laser honing technology to cylinder bore surface of CA6DF2-26 diesel engine,based on Q switched diode-pumped solid-state(DPSS) Nd:YAG laser.
基于声光调Q技术的二极管泵浦固体光源(DPSS)Nd:YAG激光器,采用"单脉冲同点间隔多次"激光微加工工艺,对CA6DF2-26型柴油机气缸套内孔表面进行激光珩磨加工。
4) Honing Stones
珩磨条
1.
Research on the CBN Honing Stones for Quenching Steel Pieces;
淬火钢用CBN珩磨条的研制
5) honing
[英][həun] [美][hon]
珩磨加工
1.
This paper introduces some common quality defects in the deep hole honing,and analyzes on the causes of these defects.
介绍了深孔珩磨加工中容易出现的孔径超差、珩磨表面粗糙度达不到工艺要求、圆度误差超差和孔的直线度误差超差等质量缺陷,并分析了其产生的原因。
2.
The application of the IKEGAI s U axis tool on the IKEGAI s machining center is introduced and the examples of compound machining(turning,boring,honing) for complex parts by using the U axis center are presented.
分析了池贝U轴刀具的原理、特点和功能,介绍了U轴刀具在池贝加工中心上的应用,提出了利用U轴加工中心对复杂零件进行复合加工(车削加工、镗加工、珩磨加工等)的实例。
6) honing oil
珩磨油
1.
It is determined the formulation of honing oil YKM9601 by investigating base Stocks and additives.
通过对基础油和添加剂的考察,确定了YKM9601珩磨油的配方。
2.
The fonnulated honing oil has good wash and extreme pressure performances by investigadon base oil and additives, the application result shows that the performances of fonnulated honing oil reaches the level of import honing oil.
通过对基础油、添加剂的考察,研制的珩磨油具有良好的清洗和极压性能,使用表明研制的珩磨油性能达到了进口珩磨油的水平。
3.
The base stock of honing oil is presented with focus on discussing EP anti - wear additive and viscosity index improver properties.
对研制的珩磨油基础油进行了分析,着重考察了极压抗磨剂、增粘剂对珩磨油性能的影响,确定了最佳配方,经某油嘴油泵厂实际应用,用户反应良好。
补充资料：珩磨
| 珩磨 honing 用镶嵌在珩磨头上的油石（又称珩磨条）对精加工表面进行的精整加工。又称镗磨。主要加工直径5～500毫米甚至更大的各种圆柱孔，孔深与孔径之比可达10或更大。在一定条件下，也可加工平面、外圆面、球面、齿面等。珩磨头外周镶有2～10根长度约为孔长1／3～3／4的油石，在珩孔时既旋转运动又往返运动，同时通过珩磨头中的弹簧或液压控制而均匀外涨，所以与孔表面的接触面积较大，加工效率较高。珩磨后孔的尺寸精度为IT7～4级，表面粗糙度可达Ra0.32～0.04微米。珩磨余量的大小，取决于孔径和工件材料，一般铸铁件为0.02～0.15毫米，钢件为0.01～0.05毫米。珩磨头的转速一般为100～200转／分，往返运动的速度一般为15～20米／分。为冲去切屑和磨粒，改善表面粗糙度和降低切削区温度，操作时常需用大量切削液，如煤油或内加少量锭子油，有时也用极压乳化液。 |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条